滲漏控制劑 的英文怎麼說

中文拼音 [shènlóukòngzhìjì]
滲漏控制劑 英文
filtration-control agent
  • 滲 : 動詞（液體慢慢地透過或漏出） ooze; seep
  • 漏 : Ⅰ動詞1 （從孔或縫中滴下、透出或掉出） leak; drip 2 （泄漏） divulge; disclose; leak 3 （遺漏） le...
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 劑 : Ⅰ名詞1 （藥劑; 制劑） a pharmaceutical or other chemical preparation 2 （某些有化學作用的物品） a...
  • 滲漏 : percolation; seepage; leakage
  1. By improving foundry method, controlling composition, choosing appropriate inoculant and using te - coating, the shrinkage defect could be reduce effectively

    通過改進鑄造工藝、控制鐵液成分、選擇合適的孕育劑、使用碲塗料等綜合控制手段，能有效降低縮松缺陷率，防止缸蓋的滲漏現象。
  2. First, according to the demand of vimp for resin system, the reaction kinetics and rheological of up resin are investigated and the optimal content of low additive profile ( lpa ) is determined. then vimp based on a high - permeable medium and grooves are studied by visual experiments, through which the appropriate high - permeable mediums are selected and the parameters of width, depth and spacing for flow grooves and spacing for supply grooves are optimized. furthermore, various factors affecting the mold filling process are discussed and the whole vacuum infusion procedures are described taking examples of the manufacture of a model boat and a sandwich panel in one infusion

    文中首先根據vimp對樹脂體系的要求，對vimp用不飽和聚酯樹脂體系的動力學和流變學性能進行了研究，確定了最佳低收縮添加劑的含量；對高滲透介質型和溝槽型vimp開展了實驗研究，通過可視化實驗優選出較好的高滲透介質，確定了引流槽的寬度、深度和槽間距及主槽的槽間距等工藝參數並進行了優化；對影響充模過程的各種因素進行了詳細的討論，並以模型船和夾芯面板的製作為實例描述了兩種vimp的成型過程；在實驗的基礎上，建立了二維滲漏模型，採用控制體有限元法對高滲透介質型vimp進行了成型過程的計算機模擬計算，通過充模時間和流動前峰的計算值與實驗結果的比較，驗證本文所採用的數學模型和數值方法的正確性，其結果對實際生產具有一定的理論指導意義。
  3. By adjusting the proportion of cellulose acetate, acetone and h2o, the network size of cellulose acetate membrane can be controlled and the leaking of fluorescent indicator in water is prevented

    通過調整成膜配比，控制ca膜的網格大小，最大限度地防止了熒光指示劑的滲漏。
  4. Because of the intrinsic nonaquaeous of this indicator, the network size of ps membrane can be controlled and the leaking of the fluorescent indicator in water can also be prevented by adjusting the appropriate proportion among the matrix, solvent and the indicator

    將其固定於ps膜中製成ps敏感膜，由於該指示劑本質上不溶於水，在制備敏感膜時適當控製成膜配比，可最大限度地防止熒光指示劑的滲漏，因此該指示劑特別適合長期檢測溶解氧。
分享友人
分享到 Line

分享到臉書