滲碳組織 的英文怎麼說

中文拼音 [shèntànzǔzhī]
滲碳組織 英文
carburized structure
  • 滲 : 動詞（液體慢慢地透過或漏出） ooze; seep
  • 碳 : 名詞[化學] （非金屬元素） carbon （c）
  • 組 : Ⅰ名詞1 （由不多的人員組成的單位） group 2 （姓氏） a surname Ⅱ動詞（組織） organize; form Ⅲ量詞（...
  • 織 : 動詞（編織） knit; weave
  • 組織 : 1 （組織系統） organization; organized system 2 （組成） organize; form 3 [紡織] weave 4 [醫學] [...
  1. Equal channel angular processing of the pearlitic steel ( 0. 65 wt. % c ) was successfully carried out at 650 with route c in this study, obtaining a total equivalent true strain ~ 5. the microstructure evolution of pearlitic steel in ecap was investigated by means of transmission electron microscope and scanning electron microscope. the main results are as the following : 1

    本研究成功地實現了c方式650珠光體鋼65mnecap變形，累積等效真應變達到5 。並用透射電鏡、掃描電鏡研究了珠光體組織的演變特點和滲碳體的變形。主要結果如下： 1
  2. Abstract : the effect of different carburizing programs on the microstructure and thick of carburized layer of screw bevel gears has been studied, meanwhile the fatigue life of these gears has also tested

    文摘:本文研究了不同滲碳淬火工藝對螺傘齒輪組織及滲層深度等影響，並對螺傘齒輪進行了臺架疲勞測試。
  3. It is shown from results that increasing carburizing time further in the normal technology can not obviously deep the carburizing layer, but can cause nonmartensite microstructure at the bottom of the gear and coarse grain across the gear, these will heavily decrease the fatigue life of the gear

    結果表明：在正常滲碳淬火工藝基礎上再延長滲碳淬火1小時，齒輪滲碳層深度變化不大，但其齒根局部表面處有非馬組織，且晶粒尺寸易產生異常長大現象，從而致使臺架疲勞壽命明顯下降。
  4. The microstructure of lamellae pearlite has evolved ultrafine cementite particles throughout the ferrite matrix uniformly after five passes. the ferrite matrix is homogeneous grains, average grain size is - 0. 3 m. 2

    變形五道次后，片層狀的珠光體組織演變成了超細的滲碳體顆粒均勻分佈於鐵素體基體的組織，鐵素體基體為均勻的等軸晶，平均晶粒大小為0 . 3 m 。
  5. The main results are as the following : ( 1 ) the microstructure of lamellae pearlite has evolved ultrafine cementite particles throughout the ferrite matrix uniformly after four passes. the ferrite matrix is homogeneous grains, and average grain size is - 0. 3um

    主要結果如下： （ 1 ） ecap變形四道次后，片層狀的珠光體組織演變為了超細的滲碳體顆粒均勻分佈於亞微晶鐵素體基體的組織。
  6. Eddy current testing is a method suitable for testing changes occurred in the surface or subsurface of specimen. when using this method to test carburized components, the variable of eddy current signal is depend on the change of constituents " physical property in carburized layer. so it can be used to test carburized components nondestructively

    渦流檢測是一種適用於試件表面和近表面變化的檢測方法，利用渦流方法檢測滲碳件時，渦流檢測信號的變化主要取決于滲碳層組織的物理特性的變化，所以渦流檢測方法可以對金屬表面滲碳層深度進行檢測而不構成任何破壞。
  7. The network carbide and acicular martensites that existed in the microstructure of the root grooves of the spline due to improper carburating and quenching process of the shafts, led to the initiation and propagation of the intergranular microcracks and were the main reason that caused the early fracture of the shafts

    由於滲碳淬火工藝不當，在二軸花鍵槽根部的組織中產生了網狀破化物和粗大的針狀馬氏體，在外力作用下形成沿晶顯微裂紋並擴展，是導致二軸疲勞斷裂的主要原因。
  8. On the surface of annealed 45 steel, as the pearlite in it contains cementite phase and has high crystal boundary density, the nucleation and growth of deposits prefer to occur at the pearlite at the beginning during depositioa the coating exists in form of nano - polycrystal layers composed by gathering of nano - sized crystals

    在退火態45鋼表面，由於珠光體組織中含有滲碳體相且具有比較高的晶界密度，因而在沉積初期鍍層優先在此處形核和生長；鍍層在基體表面是以納米尺度的晶粒聚集在一起形成的聚晶體形式存在的。
  9. An optimized cvi - pip process has been achieved, by which the c / sic composites with 2. 1 ig / cm3 high density and uniformity are fabricated in 200 hours. the microstructure and composition of pyrolytic carbon interphase and cvi - pip silicon carbide matrix in the c / sic composites are investigated with the help of polarization microscope, scanning electron microscope, and x - ray diffraction technique, etc. the structure characteristic of pyrolytic carbon interphase and cvi - pip silicon carbide matrix, and effects of cvi - pip process on it are summarized and discussed. by growth course and feature of pyrolytic carbon interphase and cvi - pip silicon carbide matrix analyzed, a whole - course densification mechanism of lamellar - growth - pattern is proposed to explain the densification phenomenon, which makes a systematic understanding on the feature of pyrolytic carbon interphase and cvi - pip silicon carbide matrix, and the multiple stitching interface binding

    根據熱解碳中間相、 cvi - pip系sic基體相的組織構成與外貌特徵，通過對熱解碳中間相、 cvi - pip系sic基體相的生長過程和生長特徵進行分析，提出了基於層生長模式的緻密化過程理論，解釋了熱解碳中間相、 cvi - pip系sic基體相以及釘扎誘導結構多重界面的形成： （ 1 ）在1150下， cvi - sic亞基體相遵從「過飽和?凝聚?融合」機理沉積，以8f型? sic為主，同時還會有少量4h型? sic ，無游離si和游離c存在； （ 2 ） pip - sic亞基體相由非晶態sic以及彌散分佈的- sic微晶、 si - o - c和游離c組成； （ 3 ）熱解碳中間相與碳纖維增強相之間、 cvi - sic亞基體相之間形成滲透釘扎結構過渡界面， pip - sic亞基體相與摘要cvi一sic亞基體相之間形成誘導結構過渡界面。
分享友人
分享到 Line

分享到臉書