滾刀 的英文怎麼說

中文拼音 [gǔndāo]
滾刀 英文
[機械工程] hobbing cutter; hob
  • 滾 : Ⅰ動詞1 （翻轉; 滾動） roll; turn round; trundle 2 （走開; 離開） get away; beat it 3 （液體沸騰）...
  • 刀 : Ⅰ名詞1 （切、割、削、砍、鍘的工具） knife; sword 2 （形狀像刀的東西） sth shaped like a knife 3 ...
  1. Chain transmissions. profile of chain wheel hobs

    鏈傳動.鏈輪滾刀的剖面
  2. The imported equipments of italy su razor grinding equipment, germany p26 testing center, roughness contourgraph of british taylor hobson limited and japan spectral analysis apparatus etc

    包括各類型數控滾齒機、剃齒機、磨齒機、內、外圓磨床、全功能數控車床以及齒形、齒向檢測儀、滾刀綜合檢測儀等設備1300餘臺。
  3. Steam the taros till done, peel and roll - cut

    芋頭蒸熟去皮，切滾刀塊。
  4. This paper puts out the edge shapes curvilinear equations, of the edge shapes of double circular gear hob, and analyzes the tooth surfaces characterist. it also points out that the gear hob is a kind of approximate shape building cutting too ls in the whole course of using

    本文提出了直槽雙圓弧齒輪滾刀刃形曲線方程式，並進一步分析了該滾刀的齒面特性，指出該滾刀從整個使用過程看，是一種近似造型的刀具。
  5. Abstract : this paper puts out the edge shapes curvilinear equations, of the edge shapes of double circular gear hob, and analyzes the tooth surface ' s characterist. it also points out that the gear hob is a kind of approximate shape building cutting too ls in the whole course of using

    文摘:本文提出了直槽雙圓弧齒輪滾刀刃形曲線方程式，並進一步分析了該滾刀的齒面特性，指出該滾刀從整個使用過程看，是一種近似造型的刀具。
  6. The basic types and dimensions of hobs for double - circular - arc gear

    雙圓弧齒輪滾刀型式和尺寸
  7. The general technical specifications of hobs for double - circular - arc gear

    雙圓弧齒輪滾刀技術條件
  8. Calibration specification for gear hob tester

    滾刀檢查儀校準規范
  9. The wastage morphology and reasons of gear hob used in production are analyzed, the influence of the varying hobbing torque and temperature on wastage of hob is discussed in hobbing process

    摘要對生產中使用的齒輪滾刀磨損和破損形貌進行了分析，探討了滾刀磨損和破損的原因及滾齒過程中滾削力和滾削溫度的變化對滾刀磨損和破損的影響。
  10. Hobs for parallel side splines

    矩形花鍵滾刀
  11. One of tooth profiles of coarse - pitch gear ball hob is analyzed in engagement theory ， the tooth profiles of the internal gear has been derived. by comparing the tooth profile with the tooth profile of the standard internal gear, it is shown that the tooth profile is satisfying

    對大模數內齒輪球形滾刀的一種齒形進行嚙合理論分析，求出滾刀加工出來內齒輪的齒形，然後與標準內齒輪的齒形比較，結果表明：該齒形的滾刀加工的內齒輪能滿足要求。
  12. Cycloidal gear hob

    擺線齒輪滾刀
  13. Wedge hob drill head is applicable for medium harden rock layer, coarse grain granite, and it has below 9 - grade drillability. the compressive strength is no more than 10 of pull coefficient

    楔齒滾刀鉆頭適合於中硬巖層，粗晶花崗巖，可鉆性9級以下，抗壓強度在普氏系數10 。
  14. Specification for general purpose, metric module gear hobs

    米制模數齒輪滾刀通用規范
  15. Gear hobs - part 1 : dimensions of solid hobs

    齒輪滾刀.第1部分:實心滾刀尺寸
  16. Tolerances for gear hobs for fine mechanics

    精密加工裝置的齒輪滾刀的公差
  17. The general technical specifications for gear hobs

    齒輪滾刀通用技術條件
  18. Design for extension solid ground - rod with smaller diameter

    整體加長小直徑磨前滾刀的設計
  19. Tool inspection methods part 5 : hobs

    刀具產品檢測方法.第5部分:齒輪滾刀
  20. The general technical specifications for involute splines hobs

    漸開線花鍵滾刀通用技術條件
分享友人
分享到 Line

分享到臉書