澆鑄時間 的英文怎麼說

中文拼音 [jiāozhùshíjiān]
澆鑄時間 英文
casting time
  • 澆 : 澆名詞（姓氏） a surname
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  • 時 : shí］Ⅰ名1 （比較長的一段時間）time; times; days:當時at that time; in those days; 古時 ancient tim...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 時間 : time; hour; 北京時間十九點整19 hours beijing time; 上課時間school hours; 時間與空間 time and spac...
  1. The control system of mould level is crucial to improve the slab quality in the continuous casting process, pid controller is used in the traditional mould level control, and it has some defaults, such as : at the start - up or finishing period of casting or during the changeover of tundish, pid control has a bad effect, its overshoot is large and its transient time is long ; the erosion of the tundish stopper and the submersed nozzles lead to the accuracy of control become bad ; the abrupt falloff of block in the submersed nozzles makes the level acutely fluctuate, and pid control can not overcome the disturbances resulted from the change of casting speed

    結晶器液位控制系統是提高連鑄產品質量的關鍵環節，傳統的連鑄機液位控制方法採用常規的pid控制，存在如下不足：開始、結束澆注和換中間罐澆注時，控制效果差，超調量大，過渡時間長；塞棒頭和浸入式水口被腐蝕后引起控制精度差；浸入式水口堵塞物的突然脫落所引起的液位劇烈波動；無法克服拉速波動引起的擾動。
  2. The cross section area of the internal sprue of the die casting dies designed should be of proper value, and matches perfectly the fill speed, the fill time and injection pressure in case that the die casting dies fail in the design

    設計壓鑄模時應當確定恰當的內澆道截面積，並使之與充填速度、充填時間和壓射比壓保持較好的匹配，以防止壓鑄模設計的失敗。
  3. In this paper, the software for the die casting technology parameters design is built based on the optimization of the die casting system matching, and is used for the design of the die casting technology parameters, such as the cross section area of the internal sprue, the fill speed and the fill time etc

    文章基於壓鑄系統匹配優化的思想，建立壓鑄工藝設計軟體，使用軟體進行內澆道截面積、充填速度和充填時間等壓鑄工藝參數的設計。
  4. The cross - section area of the internal sprue, the fill speed, the fill time and injection pressure are important die casting technology parameters

    摘要內澆道截面積、充填速度、充填時間和壓射比壓都是重要的壓鑄工藝參數。
  5. The effect of compound casting technology and compound modification on the properties of high speed steel roll collar was studied. the results showed that compound high speed steel roll collar with high and even hardness and good bond between outer and inner layers could be gained when the modified colbalt free high speed steel in outer layer and nodular iron inner layer in connection with appropriate rotational speed of centrifugal machine, pertinent pouring interval between two kinds of the melt and moderate pouring temperature as well as surface induction heat treatment were chosen. it is indicated in industrial use that the service life of compound roll collar is higher by 5 times than that of high chromium cast iron collar

    研究了離心復合鑄造工藝和復合變質處理對高速鋼輥環性能的影響，結果表明，選用變質高碳無鈷高速鋼作外層，用球鐵作內層，選擇合適的離心機轉速、兩種金屬熔液澆注間隔時間和澆注溫度，結合採用表面感應熱處理工藝，可獲得硬度高、均勻性好、內外層結合良好的高速鋼復合輥環，用於工業生產其使用壽命比高鉻鑄鐵輥環提高5倍以上。
  6. According to simulation results we decide the location of parting face and cooling system 、 the shape and location of runner and gating system etc. after that we take the az91d magnesium alloy shell of motorcycle engine as an example to proceed fine factors ( plunger injection speed 、 pouring

    然後以az91d鎂合金摩托車發動機外殼為例，進行五因素（壓射速度、澆注溫度、鍛造時間、壓射比壓、鍛造壓力）四水平l16 （ 45 ）正交實驗，在普通壓鑄過程中關閉鍛造功能。
  7. The alloy component and the process parameters of the precision casting ( including the exit temperature from furnace, pouring temperature, mould preheating temperature, holding time, cooling form ) have a certain influence on the problem of the blade brittles

    摘要合金含量、精鑄工藝參數（出爐溫度、澆鑄溫度、模殼預熱溫度、保溫時間、冷卻方式）對葉片脆性問題存在一定的影響。
  8. The arrow 770 produces fast and economical kerbing, eliminating the use of per cast or hand forming of kerbs, saving time and money

    箭牌770型路緣機能快速而經濟地鋪設路緣，取代了預澆鑄和手工鋪設，從而節省了時間和金錢。
  9. When the data of logistics in current process are used for input of simulating logistics in future 100 % continuous casting process, supply of hot metal from iron - making process may not satisfy the needs of 100 % continuous casting on raw materials. because planning scheme in continuous casting process depends greatly on smelting scheme in convertor vessel, it is important for operator to balance raw materials supply, smelting and casting in order to realize the scheme of 100 % continuous casting. when some equipment are work abnormally, mixer of hot metal and lf furnace can be used for logistics buffer

    用攀鋼煉鋼生產數據對模擬軟體系統進行的測試和模擬研究結果表明：模擬系統的隨機數發生演算法可以實現對作業時間的依分佈隨機抽取；在相似的輸入條件下，模擬結果與實際生產物流的時間分佈規律基本吻合，達到了模擬軟體設計的預期目標；若以攀鋼提釩煉鋼廠現工藝的鐵水輸入作為全連鑄后的輸入條件，則現工藝的物料供應能力可能難以滿足全連鑄生產的要求；連鑄機的連澆計劃對轉爐爐次計劃的編制有很高的要求，合理安排來料、煉鋼與澆鑄三者間的物流平衡關系將是保證全連鑄作業的重要條件；當出現設備異常情況時，可以利用混鐵爐與lf爐站前等待作為物流緩沖池，通過延長系統的平均物流時間來緩解因設備檢修和故障等擾動所造成的影響，確保生產的順利進行。
  10. The performance consistence of ab5 alloy in mass production is influenced by not only the quenching condition, but also the impurities such as fe, mg in mischmetal and the melting technology including the unit output, melting temperature and time, atmosphere, furnace frequency etc

    合金性能波動除受澆鑄時的冷卻條件影響外，還與稀土原料中鐵、鎂等雜質及熔煉工藝因素（包括單位產量、熔煉溫度、時間氣氛及爐頻等因素）有關。
  11. The spraying mixes developed by our company for con - casting tudish working lining has good propertles of coating and long service life. it keeps working for one cast without eating away and leaking for average over 12 hours during the whole casting. when inversion casting the residual working lining can be easily disintegrated without sticking to the ladle and no powder coming from the disintegration, and also the working environment not polluted. meanwhile magnesia - calcium spraying mix has the functions of absorbing impurities in molten steel and pruifying molten steel

    我公司開發的連鑄中間包工作內襯噴塗（塗抹）料施工時塗抹性好，使用壽命長，在整個連澆過程中能持續工作一個澆次而不蝕漏平均12小時以上，用后在翻包時殘余工作襯能順利解體，不沾包、解體產物不粉化，不污染工作環境，鎂鈣質噴塗料還具有吸附鋼水雜質，凈化鋼水的作用。
分享友人
分享到 Line

分享到臉書