激勵頻率 的英文怎麼說

中文拼音 [jīlìbīnlǜ]
激勵頻率 英文
driveng frequency
  • 激 : Ⅰ動詞1 （水因受到阻礙或震蕩而向上涌） swash; surge; dash 2 （冷水突然刺激身體使得病） fall ill fr...
  • 勵 : Ⅰ動 （勸勉） encourage; exert oneself Ⅱ名詞（姓氏） a surname
  • 頻 : Ⅰ形容詞（次數多） frequent Ⅱ副詞（屢次） frequently; repeatedly Ⅲ名詞1 [物理學] （物體每秒鐘振動...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 激勵 : 1 （激發鼓勵） encourage; impel; urge; inspire; excite; stimulate; put one on one s mettle 2 [電...
  • 頻率 : frequency; rate
  1. The experiment apparatus has been developed, which is based on software ( labview ) and hardware ( pci board ni 6024e ). the displacements and generative force at the tip of the ipmc actuators were measured with respect to the different voltages, frequents and various waveforms which include square, sinusoidal, and triangular wave

    實驗選取了不同電壓幅值，不同頻率的方波、三角波、正弦波三種波形作為電激勵信號，利用高速攝像記錄ipmc的位移變形，並通過力傳感器實測了ipmc試樣末端的輸出力。
  2. The method can be applied when the size of hull grillage beam and exciting frequencies cannot be easily changed

    該法適用於船體板架尺寸、激勵頻率不易改變的調頻情況。
  3. Analyzing the dynamic character under no power. it includes inhere frequency, shaking model. through which. i can learn the character of the bridge crane

    、分析橋機的在沒有外載激勵的情況下的動態特性這主要包括：固有頻率、振型。
  4. Finally, the paper studied the dynamic characteristics of 2. 6x13m mill system. mill system of single - pinion drives is lighten, so the design and run of mill system, bestir frequency must avoid inhesion

    邊緣傳動磨機系統是一個模態偶合較緊的系統，因此，在磨機系統的設計、運行中，應注意使激勵頻率避開系統的固有頻率，以免發生設備的早期失效。
  5. This paper researches and analyses the developments of web technology and magnetostrictive transducers from world wide region. the paper also analyes the characteristics curve of magnetostrictive transducers based on its equivalent circuit and researches the method how to make sure its syntony frequency and its electric simulation network parameters. at the same time, by using jsp technology, a magnetostrictive transducer electric simulation application is designed based on b / s three - tier system structure. the experiment data is fitted by curve fitting module. the equivalent input impedance of it with stimulate loop is separated based on the results of curve fitting and the syntony frequency and electric simulation network parameters of magnetostrictive transducers is determined by the input impedance. the method presented in this paper can determine the syntony frequency and electric simulation network parameters of magnetostrictive transducers with a better accuracy than the testing method of syntony & anti - synton y. further more, jsp, the advanced technology at current, has been used to realize a magnetostrictive transducer web electric simulation system. the system has good human computer interface and the function of resource sharing and information publishing. the research of this paper and its achievements have some practical merits in the researchful and applied fields of magnetostrictive transducer

    用java編程語言編寫的曲線擬合模塊，對輸入的實驗數據進行了最小二乘法的曲線擬合；根據曲線擬合結果可從帶激勵線圈的磁致伸縮換能器的輸入阻抗中分離出磁致伸縮換能器鐵芯在無激勵電流時由機械振動形成的等效輸入阻抗，並由此輸入阻抗確定磁致伸縮換能器的諧振頻率及電氣模擬網路參數。本課題提出的方法與傳統的諧振?反諧振法相比，能更準確地確定磁致伸縮換能器的諧振頻率及其電氣網路參數。同時，採用當前比較先進的web技術，實現了基於jsp的磁致伸縮換能器web電氣模擬系統，該系統具有良好的人機界面和資源共享、信息發布功能。
  6. Its principle is : a laminated structure ( beam or plate ) with delamination consists of undelaminated region and delaminted region which can be divided to upper and lower parts. when a low - amplitude and high - frequency excitation has the frequency close to some part ' s natural frequency, this part will resonate and certain amount of mechanical energy will convert to heat so that the delaminated region ' s temperature exceeds greatly that of the undelaminated region. therefore the delamination can be located by means of infrared thermograph

    其原理是具有脫層的層合材料構件（梁或板）包含脫層區域及未脫層區域，脫層區域分為上下兩部分，若對層合材料構件施加小振幅、高頻率的振動激勵，當激勵頻率恰好接近其中一部分的固有頻率時，該部分就會產生共振響應，部分機械能將轉化為熱能，使脫層區域的溫度遠高於未脫層區域，藉助紅外熱像儀即可顯示出脫層的位置。
  7. For the negative uniaxial crystal material, the principal mode is a hybrid guided mode, which can also be excited by the light at any frequency, but when the single mode propagation condition can not be satisfied, some of the higher order hybrid guided modes will exist in the waveguide

    對于負單軸晶體，波導的主模是混合模hgm _ 0模，該模式同樣可被任何頻率的光波所激勵；當光波波長滿足一定條件時，波導內傳輸單模，否則，將激勵起高階混合模。
  8. Principal conclusions were drawn as the following : the non compatibility of pressure or velocity of the gas on both sides of the contact surface is the cause of the formation of shock wave ; the heating effect of reflective shock wave to driving gas during charging or exhausting process is the internal mechanism of peak oscillating effect, and all the factors that influence the formation and the running of the shock wave will influence the peak oscillating frequency, cooling effect

    主要結論如下：熱分離機內激波形成的原因是射氣瞬間接觸面兩側壓力和速度不相容；峰值振蕩效應的內在機制為反射激波對充氣階段的驅動氣或低溫排氣的加熱，凡是影響激波形成及運動的因素都將對峰值振蕩頻率、冷效應及熱效應產生影響；當充、排氣時間比為0 . 1763時，最佳射流激勵頻率出現在高階峰值振蕩頻率上。
  9. Through studying the working mechanism of the composing, the paper referred the bearing ' s analyzing model and designing flow. through shearing test of high damping rubber, the paper analyzes the influence of shearing shape, shearing strain range and inspiriting frequence on the characteristic parameters ( dynamic shear elastic module, dissipation engineering module, wasted gene ). according to the rule of equivalent energy, the paper gets the hysteretic curve of hdr ' s equivalent bilinear model and parameters ' calculating formula

    本論文通過對這種分離式減震支座各組成部分工作機理的研究，提出了該分離式減震支座整體的計算分析方法和設計流程；通過高阻尼橡膠剪切試驗，分析了高阻尼橡膠剪切面形狀、剪應變幅值、激勵頻率和試件高度對特徵參數（動態剪切彈性模量、耗能模量、損耗因子）的影響。
  10. So the pipe system sends out noise because of resonance. especially the frequency 250hz of pulsating water is in close proximity to natural frequency of pipe, so the 250hz is a dangerous frequency to the pipe system. there is another reason why the noise is reached to 110db ( a ) in pump room that the noise is magnified by the cistern because of the resonance of cistern

    特別是激勵頻率為250hz的頻率分量恰好與管道系統的固有頻率相接近，其引起的管道振動對噪聲的貢獻最突出，同時也與水泵房房腔的固有頻率相接近，從而引起房腔共鳴發聲，使噪聲進一步被放大，以至於噪聲最大處高達105db （ a ） 。
  11. At last, in according to the experiment results, the interpretation of the mechanism of the slip phenomenon of prepressing - contact spring - damping system was given in this dissertation. further more, the relationship among the limit frequency, the value of prepressing, excitation frequency, the amplitude of excitation and the materiel parameter was analyzed. base on the theory analysis the limit frequency formula was given, and the contact - slip condition for engineering application was concluded

    最後根據理論研究與試驗分析的結果，分析預緊接觸式彈簧阻尼系統產生滑移現象的機理以及共振峰值漂移現象的理論解釋，並通過定性分析接觸分離時的頻率與預緊量、激勵頻率、激勵力幅值以及墊層的材料參數之間的關系，提出能定量描述系統出現滑移現象的極限頻率公式，總結了預緊接觸式結構始終保持接觸的條件。
  12. Finally finding that there are two reasons that cause vibration of pipe and noise. the one is the vibration of pump which transfers to pipe and stimulates the vibration of pipe. the second is the stimulating frequency of pulsating water is coherent with the natural frequency of pipe

    最後得出管道的振動主要是由於兩個原因，一是泵的機械振動傳遞給管道，引起管道的振動；二是由於水流的脈動激勵頻率與系統的固有頻率相吻合，引起管道的共振發聲。
  13. And then, the feasible forecasting reports will be presented combined the calculation methods with the stimulant frequency of the ship and the frequency character of the device installed on the mast. the decreasing methods of vibration are presented too in the design of mast in the future

    結合某船的激勵頻率及桅桿裝載設備的頻率特性要求，對桅桿結構設計進行了評價，如果桅桿固有頻率不滿足頻率儲備要求，也提出了桅桿設計中行之有效的減振措施。
  14. Based on the results of previous researchers, the following instigations have been carried out in this paper : ( 1 ) employing a reasonable local resonance model which can accurately embody the heat - generation behavior due to resonance and vibration - heat mode in delaminated region, the dynamic response and temperature distribution in the small delamination region of a laminated beam are formulated. influence of the excitation frequency on the temperature gradient formation is analyzed numerically, and several meaningful conclusions are drawn. ( 2 ) for laminated plates with delaminations, due to complexity of the analytical solution, the finite element method is employed to analyze their temperature distributions and satisfactory results are also obtained

    本文在前人研究的基礎上，對此方法進行了進一步的探討，主要做了以下的工作： （ 1 ）選取合理的、能夠準確反映由共振而產生熱量的行為的局部響應模型，以及合理的振動熱模式，推導了一維層合梁小脫層區域的振動響應及梁的溫度分佈，並編製程序計算了該層合梁在激勵一段時間后的溫度分佈趨勢，分析了激勵頻率對溫度梯度形成的影響，得到了一些有意義的結論； （ 2 ）對於二維層合板，由於解析解的形式異常復雜，本文採用有限元計算軟體對其溫度分佈進行了分析，也得到了較為滿意的結果。
  15. Under these assumptions, three kinds of excitations, namely, harmonic force with frequency equal to the structural fundamental frequency, harmonic force with frequency equal to half of the structural fundamental frequency and pulse force are inputted to the undamaged and damaged structures. then under the same excitation, the undamaged structural displacement responses, velocity responses, acceleration responses, jerk responses and responses of integrated displacement are compared with that of the damaged ones

    在此假定基礎上，分別將激勵頻率等於結構基頻的簡諧形激勵、激勵頻率等於結構基頻之半的簡諧形激勵和錘擊激勵輸入結構，而後比較了損傷前後結構在相同激勵下的位移響應、速度響應、加速度響應、加加速度響應和位移積分響應。
  16. The frequencies of translational actuation influence the stability of the tethered mass system. when the frequencies approach the natural frequency of the system, the period of energy exchange decreases and the amplitude of the pendulum increase. when the frequencies equal to the natural frequency of the system, resonance appears

    變幅激勵的頻率對系統穩定性有較大影響，當變幅激勵頻率接近系統固有頻率時，系統面內外能量交換周期減小，擺幅增大;當變幅激勵頻率等於系統固有頻率時，系統面內外均出現共振現象。
  17. Three kinds of excitations, namely, harmonic force with frequency equal to the structural fundamental frequency, harmonic force with frequency equal to half of the structural fundamental frequency and pulse force are applied to such four kinds of models. the displacement responses of the four kinds of models are calculated using sap2000 and the integrations of displacement responses are obtained by numerical calculations

    將三種激勵形式:激勵頻率等於結構基頻的簡諧形激勵、激勵頻率等於結構基頻之半的簡諧形激勵和錘擊激勵分別施加在這四種模型上，通過計算得到四種模型的位移響應，進而得到位移積分響應。
  18. We apply fuzzy control theory to active control over engine body vibration, design fuzzy control system which combines intelligent control with feedback control. this control strategy mends the flaw of complexity, nonlinear and uncertainty when we use traditional control method. by measuring rotate speed and vibration speed of i. c

    在主動控制的基礎上，採用了模糊控制的演算法，設計了內燃機整機振動模糊控制器，改進了傳統控制方法在處理振動復雜性、非線性和不確定性等方面的缺陷，通過測量內燃機轉速和內燃機整機振動速度信號，動態地改變動力減振器的剛度，使減振器的固有頻率跟隨內燃機整機振動激勵頻率的變化，達到降低內燃機振動的目的。
  19. It is important rules that research for dynamic characteristics of the mill system of single - pinion drives in operation to prevent damage from the resonance between fix frequency and bestir frequency in this paper, the pattern of pinion - - - drive shaft - - - decelerator gear vertical vibration in the mill system of single - pinion drives is established

    最後，對2 . 6 13m的磨機系統進行了動態特性的實例分析。研究邊緣傳動磨機系統的動態特性，對避免由於激勵頻率接近或等於系統的固有頻率而導致共振及設備的失效，預測系統在可能激勵下的響應特性，優化系統結構等等都具有很重要的意義。
  20. Based on mechanical vibration theory, with the torque divider ' s structure unchanged, there exist two kinds of approach to reduce the resonance : one is keeping the bending vibration frequency away from the excitation frequency, the other is increasing the modal damp

    根據機械振動理論，在不改變分動器結構設計的條件下，採用兩種方法降低螺栓共振響應：一種是將彎曲模態頻率移出激勵頻帶；另一種是提高彎曲模態的阻尼比。
分享友人
分享到 Line

分享到臉書