焊劑成分 的英文怎麼說

中文拼音 [hànjìchéngfēn]
焊劑成分 英文
flux ingredient
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 劑 : Ⅰ名詞1 （藥劑; 制劑） a pharmaceutical or other chemical preparation 2 （某些有化學作用的物品） a...
  • 成 : Ⅰ動詞1 （完成; 成功） accomplish; succeed 2 （成為; 變為） become; turn into 3 （成全） help comp...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  1. Reference composition of fluxes used for soft soldering

    軟釬焊用助熔劑的標準成分
  2. Soldering pastes - part 1 : composition, technical specifications

    焊劑.第1部分:成分和技術規范
  3. Based on the analysis and practice of the ultrasonic soldering process, the results show that it is important to procure high soldering quality on controlling submersion depth, the ultrasonic soldering time, assembling clearance and solder composition

    根據對超聲波釬焊工藝的分析和實踐，結果表明控制產品在釬焊時的浸沒深度與產品裝配間隙、超聲波釬焊時間和釬劑成分是獲得高釬焊質量的重要條件。
  4. The analysis results indicate that the correlative influence factors to the technological capabilities of electronic solders include the composition and purity and chemical uniformity of solder alloy, the composition and properties of mother materials and their clean level on the surface, the surface tension of liquid state solders, the temperature and atmosphere in soldering and the activity of flux, the chemical composition and structure and properties of the surface film of melting solders, and so on

    分析表明：相關的影響因素主要包括合金的組成、純度和化學均勻性；母材的成分、性質和表面的潔凈度；液態焊料的表面張力；釬焊溫度、氣氛、助焊劑的活性；液態焊料表面膜的組成、結構和性能等。
  5. Reference composition of wires with incorporated flux used for soft soldering

    軟釬焊用混合助熔劑焊絲的標準成分
  6. It was found that the interfacial bonding of 93w - ofc was both the joining action of ofc / w grains and that of ofc / ni - fe binders, whereas the joining of ofc to tc4 could be seen as the mutual intense diffusion effect between ofc / tc4 and as a result cu - ti intermetallic compounds were formed at the joint. the joining of tc4 - a1 and a1 - mb2 were also attributed to the result of diffusion between elements ti - al and al - mg respectively. on the other hand, residual thermal stress and stress - induced distortion were produced at the joint simultaneously due to the difference in thermal expansion coefficient of different welding " materials

    研究表明， 93w與ofc的界面連接是ofc與93w中w晶粒的連接以及ofc與93w中ni - fe粘接劑的連接共同作用的結果； ofc與tc _ 4連接界面的形成是由於ofc與tc _ 4之間發生反應擴散，並由此在二者接頭處生成了cu - ti金屬間化合物的中間相； tc _ 4 - al的連接與al - mb _ 2的連接則分別是其基體元素ti 、 al之間和al 、 mg之間元素互擴散的結果，另外，由於熱膨脹系數的差異，擴散焊接后在不同焊件的接頭處存在殘余熱應力並由此引起接頭的形變。
  7. Effect of single constituent fluoride flux on argon arc welding seam forming of ti alloy

    單組分氟化物焊劑對鈦合金氬弧焊焊縫成形的影響
  8. It will cause the paste oxidation and lose flux ratio balance if it is exposed for long - time

    錫膏與空氣長時間接觸后，會造成錫膏氧化、助焊劑比例成分失調。
分享友人
分享到 Line

分享到臉書