焊后殘余應力 的英文怎麼說
中文拼音 [hànhòucányúyīnglì]
焊后殘余應力
英文
residual welding stress- 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
- 殘 : Ⅰ形容詞1 （不完整; 殘缺） incomplete; deficient 2 （剩餘的; 將盡的） remnant; remaining 3 （兇惡...
- 余 : Ⅰ動詞（剩下） remain; leave: 9減4 余 5。 nine minus four is five ; four from nine leaves five ; i...
- 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
- 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
-
The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased
本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。Friction stir welding process can improve mechanical properties as well as decrease distortion and residual stress
採用攪拌摩擦焊連接鎂合金可以避免熔焊時產生的焊接缺陷，且具有焊后變形小、殘余應力小等優點。It was found that the interfacial bonding of 93w - ofc was both the joining action of ofc / w grains and that of ofc / ni - fe binders, whereas the joining of ofc to tc4 could be seen as the mutual intense diffusion effect between ofc / tc4 and as a result cu - ti intermetallic compounds were formed at the joint. the joining of tc4 - a1 and a1 - mb2 were also attributed to the result of diffusion between elements ti - al and al - mg respectively. on the other hand, residual thermal stress and stress - induced distortion were produced at the joint simultaneously due to the difference in thermal expansion coefficient of different welding " materials
研究表明， 93w與ofc的界面連接是ofc與93w中w晶粒的連接以及ofc與93w中ni - fe粘接劑的連接共同作用的結果； ofc與tc _ 4連接界面的形成是由於ofc與tc _ 4之間發生反應擴散，並由此在二者接頭處生成了cu - ti金屬間化合物的中間相； tc _ 4 - al的連接與al - mb _ 2的連接則分別是其基體元素ti 、 al之間和al 、 mg之間元素互擴散的結果，另外，由於熱膨脹系數的差異，擴散焊接后在不同焊件的接頭處存在殘余熱應力並由此引起接頭的形變。
分享友人