焊接層間溫度 的英文怎麼說

中文拼音 [hànjiēcéngjiānwēndù]
焊接層間溫度 英文
weld interpa temperature
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 層 : i 量詞1 （用於重疊、積累的東西 如樓層、階層、地層） storey; tier; stratum 2 （用於可以分項分步的...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  • 溫度 : [物理學] temperature
  1. The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique

    通過對其焊接性能的試驗研究，制定了該類鑄鋼件（磨耗板）的補焊工藝：低氫型堿性焊條，預熱與緩冷相結合的工藝措施，嚴格控制層間溫度（ 250 ~ 300 ）及焊接工藝規范，可獲得滿意的修復質量。
  2. Direct connect vias conduct so much heat away from the pin and into the plane that high temperature or long soldering time may be required to complete the joint - thermal damage could occur to both the board and the component from soldering or desoldering

    在焊接時，直接連接的過孔會通過引腳把大量的熱傳導至內電層，因此完成焊接就需要很高的溫度或者延長焊接時間，這就會導致在焊接或拆焊時發生電路板或元件的損壞。
  3. In the interface an interdiffused layer with multphases would be formed during the process of welding or operation at elevated temperature. because of so much difference between the interdiffused layer and the original interface layer, it would influence the welding strength severely

    在焊接過程中以及經過較高使用溫度的長時間使用后，鈮合金同不銹鋼界面會產生材料組分元素的互擴散，形成互擴散層，互擴散層的性能與原始界面的性能有較大差別，影響焊接強度。
  4. Welding. guidance on the measurement of preheating temperature, interpass temperature and preheat maintenance temperature

    焊接.預熱溫度層間溫度和預加熱的維持溫度的測量導則
  5. Welding - guidance on the measurement of preheating temperature, interpass temperature and preheat maintenance temperature iso 13916 : 1996 ; german version en iso 13916 : 1996

    焊接.預熱溫度層間溫度和預加熱維持溫度測量導則
分享友人
分享到 Line

分享到臉書