焊接檢查 的英文怎麼說
中文拼音 [hànjiējiǎnzhā]
焊接檢查
英文
welding inspection- 焊 : 動詞(用熔化的金屬修補金屬器物或使金屬工件連接起來) weld; solder
- 接 : Ⅰ動詞1 (靠近;接觸) come into contact with; come close to 2 (連接; 使連接) connect; join; put ...
- 檢 : Ⅰ動詞1 (查) check up; inspect; examine 2 (約束; 檢點) restrain oneself; be careful in one s c...
- 查 : 查名詞1. [植物學] (山查) hawthorn; haw2. (姓氏) a surname
- 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
- 檢查 : 1 (用心查看) check up; inspect; examine; censor; survey rummage; review; jerque; docimasia 2 (...
-
Fourth, the paper treats two kinds of hoisting projects of high alititude construction in bulk and member assembly, hositing machine and plan layout, setting up scaffold and joints, and installing trunks, branches and joints etc. then in detail discusses the method which applys total station to measure three - dimensional coordinate of dendriform structure, including selecting survey sign points, creating survey system and converting survey coordinate system etc. the paper also deep research on the welding performance, welding method, welding process, welding stress and control, welding strain and rectification, weld defects analysis and weld quality inspection, and so on complicated heterogeneity steel weld proplems
接著系統的論述了高空散裝法和分單元安裝法兩種樹狀結構吊裝方案,樹狀結構吊裝機械及平面布置,樹狀結構胎架及節點的搭設,以及樹狀結構樹干、樹枝和節點的吊裝工藝等諸多工藝問題。詳細的論述了採用全站儀對樹狀結構進行空間三維坐標測量的方法,包括測量標志點的選取、測量系統的建立及測量坐標的轉換等問題。深入地研究了樹狀結構可焊性、焊接方法、焊接工藝、焊接應力及控制、焊接變形及矯正、焊接缺陷分析及焊接質量檢查等復雜的異種鋼焊接問題。Available options and accessories such as ground plate, lift off protection, upper welding plate and welding gauge make the module extremely versatile and ensure a very easy installation and safe operation under rugged conditions
可選配件有接地板吊裝保護上焊接板及焊縫檢查樣板。這些配件使模塊能用於各種用途,保證安裝方便,且在凹凸不平的情況下也能安全操作。The examination must occur within the seven ( 7 ) months prior to the scheduled date of your welding inspection examination or re - certification anniversary date
此檢查必須在您預定參加之焊接檢驗考試或再次認證日期前七個月內進行。7 the completed visual acuity record must be presented prior to taking cwi examination
參加焊接檢驗師考試前必須出示完整視力檢查報告。Make dimensional and welding checking for materials, outsourcing materials. mechanical materials and products according to mechanical drawings and standard
根據圖紙及標準要求對原材料、外協件、加工件、產品等進行尺寸,外觀及焊接檢查。Longitudinal and circumferential weld seams are pl inspected for class 150 #, for other classes will be inspected with x - rays and / or us
過濾器之縱向和周圍焊接縫是染色探傷檢查,其它將以x -射線和/或超音波檢查。The conclusion of reappearing analysis is that crane bridge be used as usual because main weld maximum stress of upper cover plate of main beam lower than yield limit though it higher than permissible stress. inner stress of secondary beam was over ultimate strength, and deforming is ultra big. so it was unfit for produce and secondary beam must be changed
再現分析得出的主要結論為:橋架的主樑上蓋板主焊縫的最大應力超過了許用應力,但小於屈服極限,可以繼續投入使用;副梁內部的應力遠遠超過了強度極限,變形特別嚴重,不能滿足生產要求,因此更換新的副梁;端梁內部的應力超過了屈服極限,小於強度極限,在應力較大的位置焊接補強板;投入使用后,要對整個橋架進行定期檢查。Method of inspection for gas pressure welded joint of steel bars for concrete reinforcement
混凝土增強用鋼筋加壓氣焊接頭的檢查方法According to these, the paper put forward some countermeasures : select low carbon steel or low metal alloy steel with lower intensity, like 20r steel ; while welding, adopt strict craft measures with lower welding heat to input ; after jointing, proceed the whole hot dissolving on time ; control each welding joint with hardness hb 185 ; add 0. 25 % water into the liquid ammonia as decay eclipse ; enhance checking in operation, repairing equipment in time through regular interior and exterior checking
針對上述原因提出了防止氨冷器類臨氨壓力容器產生應力腐蝕裂紋的對策:選用強度稍低,但抗裂性較好的低碳鋼和低合金鋼,如用20r鋼製造;焊接時應採用嚴格的工藝措施和較低的焊接熱輸入量;焊后應及時進行整體消除應力熱處理;控制焊接接頭各區硬度hb 185 ;在液氨中添加0 . 25 %的水作為緩蝕劑;在運行中加強檢查,及時進行停車檢修時的內外部檢查和定期檢驗。Aws will not release your exam results without a completed visual acuity record on file
若送件資料中沒有完整的視力檢查報告,美國焊接工程協會將不會發布您的考試成績。Eye examination results shall be submitted on record forms furnished by the aws certification department
請使用美國焊接工程協會證照部門所製作的表格填寫視力檢查結果。Review the weld inspection reports for each project and rectify any possible documentation errors
審查焊接檢驗報告,修改文件上可能的錯誤Before apply the test, all the welding work of block or section should be finish and accepted by view inspection
當片體、分段組立裝配焊接完工後,經焊縫外觀檢查合格后,就可進行角焊縫密性試驗。( 3 ) the weld of pe pipe ca n ' t be proof - test by undestroyed probing. pe pipe must be welded by auto fusion equipment and reduce the man - made factor to the minimum at the same time. the operator must be well skilled and highly responsible, who performs upon weld quality control regulations, and check up the weld strictly after fusion
( 3 )聚乙烯管道連介面由於不能象鋼管焊口那樣通過無損檢測手段來驗證是否合格,所以一定要使用自動化程度高的連接機具,將人為因素降到最低,並要求焊工除了熟練的操作技術外還應具備高度責任心,嚴格執行連接施工工藝質量控制要點和有關操作要領,焊接完后採取必要的檢查驗收手段。Welding and allied processes - environmental check list
焊接和相關工藝.環境檢查表Transportable gas cylinders - periodic inspection and testing of welded carbon steel gas cylinders
可運輸儲氣瓶.焊接碳鋼儲氣瓶的周期性檢查和試驗A number of special blitz operations were also organised on safety of working - at - height, scaffold, container handling, gas welding and flame cutting, fire and chemical, and plant and machinery
我們亦組織了多次突擊檢查行動,以檢查高空工作、棚架、貨櫃處理、氣體焊接及火焰切割、防火和化學品,以及工業裝置及機械的安全。A number of special blitz operations and campaigns were also organised on the safety of work at height, scaffold, container handling, gas welding and flame cutting, fire and chemical, and plant and machinery
我們亦組織了多次突擊檢查行動,以檢查高空工作、棚架、貨櫃處理、氣體焊接及火焰切割、防火和化學品,以及工業裝置及機械的安全。Check and ensure the soldering machine and tools are in good condition and safe before starting to jointing
焊接工作開始前,首先檢查焊機和工具是否完好和安全可靠。Applicants may submit completed visual acuity records at the cwi exam location
應試者可於焊接檢測師考場繳交視力檢查報告。分享友人