焊接裂接 的英文怎麼說
中文拼音 [hànjiēlièjiē]
焊接裂接
英文
weld crack-
In addition to, the fatigue crack between web and upper flange of welded steel crane beam on heavy duty service was discussed, and based on long - term observation and research, the author classified fatigue crack into bearing type and middle type crack along the horizontal direction. the causation, distributive law and mechanism of the crack were analyzed, and the precautions to take and the measures to remedy crack were presented. the main defacts including damage, crack, erosion and aging in structures, especially in concrete structure were introduced ; the defact mechanism was analyzed and the precautions to take were also given
另外,作者對重級工作制焊接鋼吊車梁腹板與上翼緣連接焊縫的縱向水平疲勞裂縫進行了長期的觀察和研究,根據疲勞裂縫產生的不同機理,將其分為支點裂縫和肋間裂縫,並討論了兩類裂縫產生的原因、分佈規律、機理以及防治的措施;對工程中經常遇到的結構構件,尤其混凝土構件的幾種主要病害(損傷、裂縫、腐蝕與老化)進行了機理分析並提出了防治措施。To evaluate fracture instability, the total sum of stresses due to residual welding or rolling stresses, dead load, and live loads must be considered.
計算斷裂失穩性時,必須考慮焊接或軋制殘余應力,恆載應力和活載應力之總和。The calculation results indicate that the outboard of drum walls fall in plastic yielding at the same time the rising cooling water reaches the height of that point and the yield region becomes narrower and narrower when it comes closer to the circumferential strake weldments, which explains the reason coke drums experience bulging and cracks occur in the weld seams portions of shell to shell after long in service
計算結果表明:塔壁外側在冷卻水面到達的瞬間進入塑性屈服,筒節中部塑性屈服區較大,當靠近焊縫時塔壁的塑性變形區逐漸縮小直至消失,塔壁塑性屈服區的分佈特點解釋了塔體長期使用后發生鼓凸變形及簡體與焊縫連接處產生裂紋的原因。When lifting the flat boxes the board cracks at the remaining board bridges and after welding the final piece does not bend at right angles
當抬起箱子時,紙板在餘下相連處斷裂,重新焊接后,最後一片的彎曲角度不正確。The steel models the grill to use the high quality pe raw material and the high quality carbon spring steel wire and increases high quality anti - purifications and so on ultraviolet ray medicinal preparation and antioxidant becomes, the anti - break force is high, the welding is reliable, break elongation ratio low ( 3 % )
鋼塑格柵採用優質pe原料及優質碳素彈簧鋼線並添加優質抗紫外線劑及抗氧劑等精製而成,抗斷裂強力高,焊接牢固,斷裂延伸率低( 3 % ) 。Welding and allied processes. cold cracking on implants. test method
焊接和相關工藝.插銷的冷裂.試驗方法Destructive tests on welds in metallic materials - cold cracking tests for weldments - arc welding processes - general
金屬材料中焊接的有損檢驗.焊接的冷裂試驗.弧焊工藝.總則Destructive tests on welds in metallic materials - cold cracking tests for weldments - arc welding processes - part 1 : general
金屬材料焊接的有損檢驗.焊件的冷裂試驗.弧焊工藝.第1部分:總則Treatment on welding crack on connecting plate of turbine at ertan hydropower project
二灘水電站水輪機連接板焊接裂紋處理The whole name of this steel is lower weld crack sensitivity steel o7mncrmov ( shorted as wdl )
該鋼種的全稱為低焊接裂紋敏感性07mncrmov系列鋼(簡稱wdl鋼) 。Weldability testing - method of cracking test for welded tee joint
型接頭焊接裂紋試驗方法In the light of hydrogen manufacturing coverted furnace tube system ( including conversion tube, gas gathering tube and pigtail tube ) occuring weld fissure during manufacture and installation, the reason of fissure is analized. the repair plan and specific repair measures are recommended
針對制氫轉化爐管系(包括轉化管、集氣管、豬尾管)在製造安裝過程中出現焊接裂紋的原因進行了分析,並介紹了缺陷的修復方案和具體修復措施。Weldability testing - method of y - groove cracking test
型坡口焊接裂紋試驗方法Method of controlled thermal severity weld cracking test
受控的熱嚴酷焊接裂紋試驗方法Method of h - type restrained weld cracking test
H形限制焊接裂紋試驗方法Weldability testing - method of fisco cracking test
焊接裂紋試驗方法Method of u - groove weld cracking test
U形坡口焊接裂紋試驗方法Method of y - groove weld cracking test
Y型坡口焊接裂紋試驗方法Low welding crack susceptibility high strength steel plates
低焊接裂紋敏感性高強度鋼板Quantitative evaluation study on metal magnetic memory of welding cracks
焊接裂紋的金屬磁記憶定量化評價研究分享友人