焊接裂紋 的英文怎麼說
中文拼音 [hànjiēlièwén]
焊接裂紋
英文
weld crack-
This indicated that the fracture had initiated at the unfused butt weld in the longitudinal stiffener.
研究表明裂紋是從縱向加勁助未熔透的對接焊縫中起始的。Some crack extension probably developed from the unfused section of the butt weld across the thickness of the stiffener during transport and erection.
有些裂紋可能在運輸和安裝過程中就從加勁肋對接焊未熔透處開始發展。Cracks have been found in the flange and web splices at groove welds in at least four bridges.
至少在四座橋梁的翼緣板和腹板拼接坡口焊縫中發現了裂紋。The calculation results indicate that the outboard of drum walls fall in plastic yielding at the same time the rising cooling water reaches the height of that point and the yield region becomes narrower and narrower when it comes closer to the circumferential strake weldments, which explains the reason coke drums experience bulging and cracks occur in the weld seams portions of shell to shell after long in service
計算結果表明：塔壁外側在冷卻水面到達的瞬間進入塑性屈服，筒節中部塑性屈服區較大，當靠近焊縫時塔壁的塑性變形區逐漸縮小直至消失，塔壁塑性屈服區的分佈特點解釋了塔體長期使用后發生鼓凸變形及簡體與焊縫連接處產生裂紋的原因。Method of t - joint weld cracking test
T型接頭焊縫裂紋試驗方法Abstract : in this article, some problems existing in the design of apheroidal tank were briefly stated, including the advantages and disadvantages of use of quenched and tempered high strength steel as the material of spheroidal tank shell, thedividing type of the shell, the welding process and the occurrence of the welding crack. thenmthe measures to solve these problems were proposed
文摘:本文簡述了調質高強度鋼用於球罐殼體材料的優缺點和球罐設計中有關球殼的分割方式，焊接製造加工工藝，焊接裂紋的防止等問題，並提出了相應的建議。In this article, some problems existing in the design of apheroidal tank were briefly stated, including the advantages and disadvantages of use of quenched and tempered high strength steel as the material of spheroidal tank shell, thedividing type of the shell, the welding process and the occurrence of the welding crack. thenmthe measures to solve these problems were proposed
本文簡述了調質高強度鋼用於球罐殼體材料的優缺點和球罐設計中有關球殼的分割方式，焊接製造加工工藝，焊接裂紋的防止等問題，並提出了相應的建議。( 3 ) the transformation for turbo cycling compressor is designed in both differential pressure seal parts at the inlet and outlet and the connecting construction of the positioning key and turbo cycling compressor casing : replace wave pipe of differential pressure seal parts with asbestos jointing and improve its reliability ; jointing connection of the positioning key and turbo cycling compressor casing has been converted into screw thread connection and avoid the dangers from jointing crack
（ 3 ）從進出口壓差密封部件和定位鍵與外殼間聯接結構兩方面入手，提出了相應的改造方案：將機組進出口壓差的密封部件由波紋管改為石棉填料函，提高了其運行可靠性；將內件周向定位鍵與外殼間的聯接結構由焊接改為螺紋聯接，避免了焊接裂紋引起的安全事故。Treatment on welding crack on connecting plate of turbine at ertan hydropower project
二灘水電站水輪機連接板焊接裂紋處理The whole name of this steel is lower weld crack sensitivity steel o7mncrmov ( shorted as wdl )
該鋼種的全稱為低焊接裂紋敏感性07mncrmov系列鋼（簡稱wdl鋼） 。Weldability testing - method of cracking test for welded tee joint
型接頭焊接裂紋試驗方法In the light of hydrogen manufacturing coverted furnace tube system ( including conversion tube, gas gathering tube and pigtail tube ) occuring weld fissure during manufacture and installation, the reason of fissure is analized. the repair plan and specific repair measures are recommended
針對制氫轉化爐管系（包括轉化管、集氣管、豬尾管）在製造安裝過程中出現焊接裂紋的原因進行了分析，並介紹了缺陷的修復方案和具體修復措施。Weldability testing - method of y - groove cracking test
型坡口焊接裂紋試驗方法Method of controlled thermal severity weld cracking test
受控的熱嚴酷焊接裂紋試驗方法Method of h - type restrained weld cracking test
H形限制焊接裂紋試驗方法Weldability testing - method of fisco cracking test
焊接裂紋試驗方法Method of u - groove weld cracking test
U形坡口焊接裂紋試驗方法Method of y - groove weld cracking test
Y型坡口焊接裂紋試驗方法Low welding crack susceptibility high strength steel plates
低焊接裂紋敏感性高強度鋼板Quantitative evaluation study on metal magnetic memory of welding cracks
焊接裂紋的金屬磁記憶定量化評價研究分享友人