熱壓制 的英文怎麼說

中文拼音 [rèyāzhì]
熱壓制 英文
hot pressing
  • 壓 : 壓構詞成分。
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  1. This thesis reports some results on the hot press sintering of nano - composite wc - co powder, which is prepared by spray pyrogenation & continuous deoxidization and carbonization process

    本課題採用熱壓燒結技術對以噴霧熱解?連續還原碳化法制備的納米復合wc - co粉末進行了熱壓燒結研究。
  2. In chapter two, we fabricated r - ni - fe / al2o3 nanocomposites successfully by using ball - milling mixing method plus hot - pressing process. meanwhile, their microstructures are characterized by x - ray diffraction ( xrd ) analyser, transmission electron microscopy ( tem ), field emission scanning electron microscopy ( fe - sem ) and brunauer - emmett - teller ( bet ). the results indicate that ni - fe particles are homogenously dispersed in the matrix in the composites

    在第二章中，我們採用高能球磨混合方法加上熱壓燒結工藝，成功制備了ni - 20fe al _ 2o _ 3納米復合材料，並通過x射線衍射儀（ xrd ） 、透射電鏡（ tem ） 、場發射掃描電鏡（ fe - sem ） 、比表面孔隙儀（ bet ）對該復合材料的微結構進行了表徵。
  3. Sicp / al matrix composites, with 5, 15 and 25 % volume fraction of sic particles, were prepared by vacuum hot - pressing sintering processing in this paper. based on mechanics properties, sem observation and energy dispersive x - ray analysis, the interface reaction phenomenon of sicp / al composites made by vacuum hot - pressing sintering, as well as the reinforcement and fracture mechanisms of this composite were analyzed. the dynamic responses of sipc / al composites were studied by a split hopkinson high - speed pressure bar impact system which strain rate was from quasistatic state strain rate ( 3. 3 10 - 3s - 1 ) to dynamic state strain rate ( 5. 2 103 s - 1 )

    本研究以武裝直升飛機防護裝甲材料為研究對象，採用真空熱壓粉末冶金燒結工藝制備了含sic顆粒體積分數分別為5 、 15和25的sic顆粒增強鋁基復合材料，結合其力學性能、掃描電鏡和界面微區能譜分析結果，分析了sic _ p al復合材料的真空燒結過程中的界面現象，以及材料增強和斷裂機理，並利用hopkinson高速壓桿沖擊實驗系統對其從靜態到動態（應變率為3 . 3 10 ~ （ - 3 ） s ~ （ - 1 ） 5 . 2 10 ~ 3s ~ （ - 1 ） ）的壓縮破壞響應進行了研究，分析了不同體積分數sic _ p al復合材料高應變率壓縮載荷下，材料的變形和微觀損傷機理，以及利用高速沖擊空氣炮測定了改復合材料制備剃度復合板的穿透性能。
  4. For instance : continuous type flat to hot press develop successfully, make shaving board and mdf production line realize take in succession completely, not only give full play to the ability to produce production of the mechanical equipment on the line, but also in order to realize automatic control and automatic monitoring of product quality of the production process have created the condition

    如：連續式平壓法熱壓機的研製成功，使刨花板和mdf生產線實現了全線連續化，不僅充分發揮了生產線上機械設備的生產能力，也為實現生產過程的自動控制和產品質量的自動監測創造了條件。
  5. This machine has many accessory moulds for various kinds of colored pavement bricks, grass - planting bricks, sideway bricks and heat insulation bricks

    該機配套各種模具，可壓制各種彩色人行道板磚植草磚路側石磚隔熱層磚等。
  6. The age hardening characteristic of as - cast cu20ni20mn and cu20ni35mn alloys and the interface characteristic between the alloy and cast tungsten carbide were studied, and on the basis of this study, composites of cu - ni - mn alloy reinforced with different volume fraction ( 0 - 45vol. % ) and different size ( 42 - 362 m ) of cast tungsten carbide particles were made by vacuum hot - pressing liquid sintering technology. pin on disk two body abrasion tests have been performed with different size of sic abrasive under different loads

    本文研究了鑄態cu20ni20mn和cu20ni35mn合金的時效硬化特性及其與鑄造碳化鎢的界面特性，並在此基礎上以不同尺寸（ 42 362 m ）的鑄造碳化鎢顆粒為增強體，採用真空熱壓液相燒結技術制備了不同顆粒含量（ 0 45vol . ）的鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料；以不同粒度的sic為磨料，在不同載荷條件下利用銷?盤磨損試驗機測試了復合材料的二體磨料磨損性能。
  7. The disperse degree of the ceramic can greatly affect uniformity of the composite, which limit the poling voltage and affect the piezoelectricity. in this paper, the relationships among constitutes, microstructures, dielectric and piezoelectric properties were calculated by employing the banno unit cell mode ; pzt ceramic were synthesized by the hydrothermal method and the appropriate solution was selected according the adsorption of pvdf on the ceramic particle surface ; then, relationships between the disperse degree and the fabrication process were studied. base on these, the pzt / pvdf composites intermingled some pan were prepared and the microstructures were investigated

    論文首先利用bannounitcell模型，計算了pzt pvdf壓電復合材料的組成、結構、與其壓電和介電等性能之間的關系；針對壓電復合材料存在的均勻分散性差的缺點，選用水熱法制備的粒度均勻的pzt陶瓷粉末，並採用溶液混和法與聚合物pvdf進行分散復合，重點研究了不同工藝條件下陶瓷的均勻分散性及其與材料微觀結構之間的關系。
  8. By hot pressing, the licoo _ 2 target was produced. different moulds were used in the hot pressing including the graphite mould and the sic mould

    在熱壓法制備licoo _ 2靶材的過程中，使用了石墨模具，碳化硅模具。
  9. The experimental results demonstrate that the suitable mea hot - pressing temperature and pressure are 120 and 15. 5mpa, respectively. the optimum catalyst loading in anode is 4 mg pt / cm2, and the best contents of nafion ionomer in anode and cathode layer are 45wt % and 35. 3wt %, respectively

    實驗結果顯示，制備膜電極時最佳的熱壓溫度和壓力分別為120和15 . 5mpa ；陽極催化劑的適宜載量為4mgpt / cm2 ；陽極和陰極催化劑層的nafion最優含量分別為45 . 0wt %和35 . 3wt % 。
  10. Fesi2 - based semiconductors have been studied due to its good performance, low cost and potential application in power generation using waste heat. state - of - the - art techniques such as levitation melting, rapid solidification and hot uniaxial pressing ( hup ) were used for sample preparation in the present work. the phase transformation, micro structure and transport properties of the materials have been analysed with xrd, sem / edx, raman spectroscopy as well as thermoelectric characterization

    在綜合評述國內外熱電材料研究新進展的基礎上，本文以懸浮熔煉、快速凝固和單軸熱壓等制備工藝為技術特徵，以mn或al摻雜fesi _ 2基合金為研究對象，採用xrd 、 sem / eds 、 raman光譜以及材料熱電性能測試等分析表徵手段，系統研究相變過程、微觀結構特徵及其對材料熱電性能的影響。
  11. In this paper, nanosized al2o3 ceramic particles were chose as reinforcing phase. enhanced with ultrasonic wave the particles were covered with copper using method by electroless plating, the copper - matrix composite was developed by hot - press sintering process of the composite powder. the composition, microstructure, hardness, density and dry sliding wear property of the new material have been studied

    研究路線為：選用納米級al _ 2o _ 3陶瓷顆粒作為增強相，在超聲波的環境中用化學鍍的方法完成對納米al _ 2o _ 3陶瓷顆粒表面的金屬銅包覆，採用熱壓燒結成型技術以復合粉末為原料制備成納米al _ 2o _ 3陶瓷顆粒增強銅基復合材料，研究分析復合材料的成分、組織結構、硬度以及緻密度，對試樣進行了干滑動摩擦磨損實驗。
  12. Based on nanometer powders, cajc cvbased oxides were synthesized by constant sintering, cold isostate pressure and hot pressure methods. it can be found that sintering methods have a great influence on thermoelectric performances : the sample synthesized by hot pressure method is most dense and has the best thermoelectric performances. the microstructures and thermoelectric properties of cascog - based oxides doped by four dopants have been investigated

    採用不同的后續工藝制備最終的熱電材料，研究不同工藝對熱電性能的影響發現：熱壓燒結制備出的熱電材料最緻密，其熱電性能也最好；先冷等靜壓成型后常壓燒結方法次之；直接常壓燒結法燒出的樣品氣孔最多，性能也最差。
  13. Cable sockets, hot pressed, cast for copper conductors

    銅導線用熱壓制的鑄塑的電纜端頭
  14. Cracking analysis on hot formed stainless steel elliptical head

    不銹鋼橢圓封頭熱壓制裂紋分析
  15. Hot rolled asphalt for roads and other paved areas - specification for constituent materials and asphalt mixtures

    道路和其他鋪砌區用熱壓制瀝青.組分材料與瀝青混合物規范
  16. Hot rolled asphalt for roads and other paved areas - specification for transport, laying and compaction of hot rolled asphalt

    道路和其他鋪砌區用熱壓制瀝青.熱壓制瀝青的運輸鋪設和壓實規范
  17. We can combine the two technique to pressing ti and al elemental powders

    並結合兩種工藝進行低溫真空熱壓制。
  18. The technique can avoid produce ti / al chemical compound in high temperature. the chemical compound would increase the difficulty of pressing. the research on vacuum degassing and temperature of pressing can acquire the ideal composite powders of highly

    對ti / al復合粉進行真空脫氣及低溫熱壓制可以降低坯料中空氣含量並提高粉末顆粒的界面結合強度，同時避免高溫下生成tial基化合物增加緻密難度，對真空脫氣及壓制溫度進行研究，獲得理想的緻密度極高的復合粉末。
  19. The material of the experiment is compact ti / al composite powders prepared by high energy ball milling. the compact ti / al composite needs reactive sintering at low temperature and high temperature, in order to get high densified tial alloy

    本文實驗方法是，球磨不同時間的ti / al復合粉，然後在一定壓力下冷壓或者300 400下熱壓制坯。
  20. The products can be widely used for molding, cold and hot pressing, assembling of the parts for industries like clocks and watches, accessories of automobile and motorcycles, tableware, badges, jewelty, electronics, cameras, metal works, rubber products, chemicals, packing, etc

    產品可廣泛用於大批量生產的鐘表、眼鏡、汽摩配件、餐具、獎章、首飾、電子、相機、五金製品、橡膠製品、化工包裝等行業的零件成形、冷、熱壓制和裝配等行業。
分享友人
分享到 Line

分享到臉書