熱板試驗 的英文怎麼說
中文拼音 [rèbǎnshìyàn]
熱板試驗
英文
hot bench test-
The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique
通過對其焊接性能的試驗研究，制定了該類鑄鋼件（磨耗板）的補焊工藝：低氫型堿性焊條，預熱與緩冷相結合的工藝措施，嚴格控制層間溫度（ 250 ~ 300 ）及焊接工藝規范，可獲得滿意的修復質量。This test chooses general industrial vc / vac copolymer as raw material, various supplement material additives are also the common conventional avirulent additive on industry ; the plastic material processing routine is also the universal method to make the thermoplastic plate of low temperature of vc / vac copolymer that accords with medical requirement that its softening temperature is 55
本試驗選用氯醋共聚樹脂為主要原材料，所用輔料添加劑也是工業上常見的無毒性常規添加劑；採用常規的塑料加工成型方法及設備製造出軟化點為55的、符合醫用要求的低溫熱塑性氯醋共聚樹脂板材。Can be used to locate cable and pc board emission " hot spots " and evaluate emc problems at the breadboard and prototype level
，可用於探測電纜和印製板的發射「熱點」並評估試驗電路板和樣機階段的電磁相容Based on the above, a surrogate models are built for thermal conductibility performance of sandwich panel with " v - type " folded core in this paper, and they can be optimized by multi - subject. the numerical simulation function and optimization design method in condition of lightest weight are shown in this paper
其次，用isight軟體重新設計了40組不同構型的試驗設計點，並以此為基礎對v型褶皺芯材夾層板的熱傳導性能構建了可用的代理模型，給出了數值模擬函數和最輕重量條件下的優化設計方法。Test methods for the thermal performance of flat plate solar collectors
平板型太陽集熱器熱性能試驗方法Standard test method for critical radiant flux of exposed attic floor insulation using a radiant heat energy source
暴露于輻射熱能源的擱樓地板絕緣的臨界輻射通量的標準試驗方法Standard method of test for critical radiant flux of floor covering systems using a radiant heat energy source
用輻射熱能源測定地板覆蓋物的臨界輻射流的標準試驗方法On the basis of test results, the effects of operation parameters such as material thickness, heating temperature and pressure of drying chamber on vacuum freeze drying are discussed. aiming at decreasing drying time and reducing energy consumption, these parameters are optimized and optimization results agree well with actual results
在三因素二次正交回歸試驗的結果分析的基礎上，利用降維分析方法探討了凍干厚度、加熱板溫度和系統的真空度對乾燥時間和乾燥能耗的影響，並對混合加熱條件下單位水分能耗和凍干生產率進行了優化分析。The design strategies of energy saving of dwelling are put forward on the planning of dwelling district, shape coefficient of building, room and envelop. this thesis puts forward the design of " stagger shading eastwards or westwards ", the design of " double skins " in dwelling and " the energy calculation method with thermal comfort of room ", and introduces the tests of " heat from south to north ", " shading for west wall " and " stagger shading eastwards or westwards "
第二方面是提出「錯列式東西向遮陽板」和在住宅中應用「雙層皮」的設想，及「考慮熱舒適要求的房間能耗計算方法」的基本思路，並探討了「南熱北送」 、 「西墻遮熱板」和「錯列式東西向遮陽板」等節能設計手法的實驗測試結果。Standard test method for steady - state heat flux measurements and thermal transmission properties by means of the guarded - hot - plate apparatus
用護熱板法測定穩態熱通量和傳導性的標準試驗方法Methods of testing vitreous enamel finishes - determination of resistance to thermal shock of coatings on articles other than cooking utensils and fabricated sheet steel components
搪瓷釉層的試驗方法.第1部分:除廚房器具和薄鋼板組件外的製品覆層耐熱沖擊性的測定Ceiling mounted radiant panels supplied with water at temperature below 120 c - test methods for thermal output
頂棚上裝有可提供120以下熱水的散熱板.熱輸出的試驗方法Ceiling mounted radiant panels supplied with water at temperature below 120 o c - part 2 : test method for thermal output
頂棚上安裝的可提供120以下熱水的輻射板.第2部分:熱輸出的試驗方法Test methods for insulation plastics sheet laminated thermosetting
熱固性絕緣塑料層壓板試驗方法An experiment was conducted to study the effects of hot - pressing temperature on properties of wheat straw - plastic composites made from wheat straw and recycled polyethylene ( pe ) using isocyanate as adhesive through multi - factor orthogonal experiment and single - factor experiment
摘要通過正交試驗和單因子試驗，以麥秸和廢舊聚乙烯塑料為原料，使用異氰酸酯膠黏劑壓制麥秸塑料刨花板，分析熱壓溫度對麥秸聚乙烯復合材料性能的影響。From experimental result, i preliminarily know that eps is good thermal insulation material because the absorption of water is low and heat insulation is good, it is practicable at preserving temperature field of frozen earth roadbed and bringing frozen disaster under control ; second, according to the analysis of the eps that is applied into practical project, i have studied the practical effect which eps preserve roadbed temperature field, and the influence that was made after building field. i have get that eps can influence moisture content and frozen upper limit, through practical measuring data, i have studied freezing and expanding quantity and melting and submerging quantity during a complete frozen and melting cycle as well as have expanded and proved the practical application effect of eps with some reference significance to deep research of some connected problems. finally, through computer data analysis, setting up the analytical model of finite unit, i have simulated the temperature field of roadbed heat preservation, then expounded and proved that the height of embankment influenced the effect of thermal insulation material
其一是對聚苯乙烯泡沫塑料（ eps ）保溫板以及天然路基土層、路堤填料進行了室內試驗分析，結合國內外現在的有關科研成果，綜合確定其各項特徵參數；從試驗結果初步認識到聚苯乙烯泡沫塑料是一種吸水率低，隔熱性好的保溫材料，在凍土路基溫度場的保護和凍害治理方面是可行的；其二通過eps保溫板在現場工程實踐中的應用分析，研究了保溫板在保護路基土層溫度場的實際效果以及修築路堤后造成的影響，保溫板對土體含水量、凍結上限的影響，通過實測資料，研究了在一個完整的凍融周期內整個路基的凍脹量和融沉變形量，論證了保溫板的實際應用效果，對有關問題的進一步研究和相關工程設計具有參考意義；其三，通過計算機數值分析，建立有限元分析模型，對保溫路基的溫度場進行了模擬計算，論證了路堤高度對保溫材料效果的影響。The saw surfacing test about tube - plank of jg600 - high - pressure heating apparatus
高壓加熱器管板堆焊焊接工藝試驗Textiles. physiological effects. measurement of thermal and water - vapour resistance under steady - state conditions sweating guarded - hotplate test
紡織品.生理效應.在穩態條件下耐熱和水蒸氣特性的測量汗蒸防熱板試驗Test methods for copper - clad thermosetting laminates for printed wiring boards
印刷書寫板用鎧裝銅熱固性層板試驗方法On basis of numerical simulation, the optimized weling technological has been vadidated and adjusted by plane test, results show that residual stress of both ends welded in advance can be decreased by the interspace welded later, and decreasing effect is the most obvious in the 50mm range of the interspace ; for local heating, it is 60mm from the edge of heated area to decrease residual stress
通過平板試驗得到了分段焊與局部加熱合理工藝參數，並在此基礎上，對轉輪的焊接殘余應力場進行了調整與控制，使葉片出水邊危險區域附近產生了較大的殘余壓應力，且轉輪整體的殘余應力水平低於轉輪材料屈服極限的三分之一。分享友人