熱殘余物 的英文怎麼說
中文拼音 [rècányúwù]
熱殘余物
英文
thermal residue-
New geological logging technical method of pyrolysis gas - chromatogram and gas chromatography is briefly introduced to evaluate light crude oil zone and residual oil zone here, involved in geology, geochemical pyrolytic parameter and geophysical method
本論文主要是利用熱解色譜、氣相色譜等地質錄井新技術評價手段，結合地質、地球化學及地球物理方法，針對輕質油層，殘余油水層識別對象開展研究。Because there are many kinds of matrixes in titanium matrix composite, we select some typical ones as investigated subject in many titanium alloys or titanium aluminide intermetallics, and then simulate the distribution of thermal residual stresses under the appropriate composites fabrication and heat treatment parameter. we not only hope to seek better titanium matrix, but also discover the relationship between the material properties and the thermal residual stresses, and then provide some theoretical guidance for the selection of the matrix in titanium matrix composites
鑒于當前鈦基復合材料中鈦基體的多樣性，我們將在各種類型的鈦合金和鈦鋁金屬間化合物中，挑選出較為典型的作為研究對象，利用本文得到的較為理想的復合材料加工和熱處理工藝參數，逐一模擬它們的殘余熱應力，找到殘余熱應力分佈較為理想的鈦基體，並且，希望能夠尋找到材料性能與熱殘余應力的相互關系，為鈦基復合材料基體的選擇提供一定的理論指導。This company produces the knitting center parts uses the material of completely high quality guards against rust the cast alloy iron, adopts the tertiary aging treatment of metal way, namely except hot aging treatment of metal, outside nature aging treatment of metal, each product in processing process, also must pass through the physical vibration aging treatment of metal process, guarantees each product the residual stress finally to obtain the elimination and the equalization
本公司生產的編織中心組件所用材料，全部使用優質防銹合金鑄鐵，採取三重時效處理方式，即除熱師時效處理、自然師時效處理外，每件產品在加工過程中，還要經過物理振動時效處理過程，確保每件產品的殘余應力最終得到消除和均化。It was found that the interfacial bonding of 93w - ofc was both the joining action of ofc / w grains and that of ofc / ni - fe binders, whereas the joining of ofc to tc4 could be seen as the mutual intense diffusion effect between ofc / tc4 and as a result cu - ti intermetallic compounds were formed at the joint. the joining of tc4 - a1 and a1 - mb2 were also attributed to the result of diffusion between elements ti - al and al - mg respectively. on the other hand, residual thermal stress and stress - induced distortion were produced at the joint simultaneously due to the difference in thermal expansion coefficient of different welding " materials
研究表明， 93w與ofc的界面連接是ofc與93w中w晶粒的連接以及ofc與93w中ni - fe粘接劑的連接共同作用的結果； ofc與tc _ 4連接界面的形成是由於ofc與tc _ 4之間發生反應擴散，並由此在二者接頭處生成了cu - ti金屬間化合物的中間相； tc _ 4 - al的連接與al - mb _ 2的連接則分別是其基體元素ti 、 al之間和al 、 mg之間元素互擴散的結果，另外，由於熱膨脹系數的差異，擴散焊接后在不同焊件的接頭處存在殘余熱應力並由此引起接頭的形變。Test methods for pigments - part 15 : loss on heating - section 2 : ignition residue
顏料試驗方法.第15部分:加熱損耗.第2節:燃燒殘余物Changing the grading of sic particles not only affects the strength and pile density, but also modifies the phase compositions and microstructure of the material. with the reducing of sic particles, the strength of the material increases obviously. the nitrification scheme has the greatest influence on phase compositions and microstructure " of si3n4 ( si2on2 ) - sic, after two continuous nitrification reacting peak and short - time high - temperature treating, the best properties can be obtained ; and the residual strength of the composite is much higher after the thermal shock resistance test, which shows that the material possesses excellent thermal shock resistance
本論文較全面地探討促進強度和顯微結構良好的si _ 3n _ 4 （ si _ 2on _ 2 ）結合相的實驗條件，實驗數據顯示：引入適量的燒結助劑能夠促進si _ 3n _ 4 （ si _ 2on _ 2 ）的生成和晶粒的長大，而過量時，其促進作用反而下降；隨著si粉加入量增加，生成的結合相明顯增多，復合材料的性能顯著提高；改變sic顆粒級配不僅影響復合材料的強度與堆積密度，而且對復合材料的物相與顯微結構也有影響，隨著顆粒逐漸細化，材料的強度有較大的提高；對復合材料的強度、物相與顯微結構影響最大的是氮化制度，經過兩個氮化高峰連續的反應和短時間的高溫后處理得到的復合材料性能最好；通過抗熱震性能實驗后復合材料的殘余強度較高，顯示出較好的抗熱震性能。分享友人