熱量排放率 的英文怎麼說

中文拼音 [liángbèifàng]
熱量排放率 英文
heat emission rate
  • : 量動1. (度量) measure 2. (估量) estimate; size up
  • : 排構詞成分。
  • : releaseset freelet go
  • : 率名詞(比值) rate; ratio; proportion
  • 熱量 : quantity of heat; heat quantity; amount of heat熱量測量 calorimetry; 熱量單位 thermal unit; heat ...
  • 排放 : discharge; blowoff; blowdown; issue; volley; emission; sluice; bleed
  1. When the water dose was 20 % and engine speed was 2000r / min, the maximum fuel saving was 4. 1 % ; the thermal efficiency of emulsified fuels was higher than that of using pure diesel oil. nox and particulates emissions were reduced greatly by using emulsified fuels. when water dose was 20 % and engine speed was 1500 r / min, the maximum nox reduction was 43. 4 % ; the average of particulates under all loads was reduced by the extent of 46 % ~ 64 %

    結果表明:燃用乳化油節油有所提高,當n = 2000r min ,摻水為20時最大節油可達4 . 1 ;燃用乳化油的也高於燃用純柴油; no _ x 、顆粒比燃用純柴油時則有大幅度降低,當n = 1500r min摻水為20時, no _ x下降的最大值可達43 . 4 ;固體顆粒物在整個負荷范圍內的平均值比燃用純柴油時低46 64 ;隨著乳化油摻水的提高,效果改善越明顯;而thc和co的則比燃用純柴油時有所升高。
  2. The disposal of the valves and intake manifold structure not only affect fresh air charge but airflow in the cylinder, which immediately affect combustion efficiency and the performance of dynamic, economic and emission. the structure of the air distributing institution has influence on charging efficiency and the noise of engine. the combustion chamber affects compression scale which has great influence on dynamical performance ; f / v which affects the exhaust of hc ; squash area and clearance which have great influence on the intensity of squash

    氣缸蓋的氣門列方式與氣道結構形式影響進氣充和氣流在氣缸內的運動,從而影響了燃燒效,對整機的動力性、經濟性以及都有直接的影響;配氣機構的形式影響充氣系數和整機噪聲等;缸蓋燃燒室決定了影響整機動力性能的壓縮比,影響hc的f / v和對擠流起決定性作用的擠氣面積以及擠氣間隙,所以燃燒室對整機動力性、經濟性、等都有重要的影響;氣缸蓋是整機負荷與應力最大的部件之一,負荷過高將不利於發動機壽命以及可靠性的提高。
  3. Weishaupt products are composed of gas , oil and dual fuel burners with rating range between 10kw and 17. 5 mw

    威索燃燒器主要分為燃氣型、燃油型和油氣兩用型三種,功范圍為10kw - 17 . 5mw ,適用於所有需經濟、安全及低廢氣運行的供設備領域。
  4. Open the air - release valve of the trap beforework to discharge a large quantity of non - frozen gas. then drivetightly the air - release valve and preheat gradually. the preheatrate should not be more than 36 / minutes

    疏水閥在工作前需打開氣閥,使不凝結氣體大出,然後擰緊氣閥,並逐漸預,預不超過36 / 8分鐘。
分享友人