燒成溫度 的英文怎麼說

中文拼音 [shāochéngwēndù]
燒成溫度 英文
burnt temperature
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 成 : Ⅰ動詞1 （完成; 成功） accomplish; succeed 2 （成為; 變為） become; turn into 3 （成全） help comp...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 燒成 : baking
  • 溫度 : [物理學] temperature
  1. Results show that : ( 1 ) for each particle size of andalusite, variation tendency of the properties of the material is generally the same : the maximum of bulk density, compressive strength and rupture strength appears in the range of 5 % - 10 % content of fiber, these properties of the material remarkably decrease as the fiber content exceed 10 % ; while at the same fiber content, the properties of the material increase with the increase of firing temperature

    結果表明： （ 1 ）對于不同粒度的原料，性能變化規律大致相同：在同一燒成溫度下，體積密度、常溫耐壓強度、常溫抗折強度在5 10之間出現峰值，加入量超過10之後材料的性能明顯下降；在相同的纖維含量下，隨著燒成溫度的提高，試樣的各項性能均有所上升。
  2. ( 2 ) the properties of the material with finer andalusite particle size are superior to those of coarse particle size at lower temperature, but properties of material of fine and coarse particle size have little difference at higher temperature. this illustrates that the andalusite particle size can lower the sintering temperature and that it brings forth not remarkable influence on the property of the material when the material is sintered completely

    （ 2 ）對于不同粒度的原料，在燒成溫度較低的情況下，粒度小的材料性能明顯高於粒度大的材料，但在燒成溫度較高的情況下，兩者差別不大，說明原料粒度減小能降低製品的燒結溫度，但在制品均完全燒結的情況下對材料性能影響不大。
  3. The main results are shown as follows : 1. bt _ 4 doped with cuo could be sintered in a lower temperature, because cuo has a low melting point. there isn ’ t any other phase in the samples. the dielectric properties decreased because cuo was non - crystalloid

    本人工作的主要研究成果如下: 1 . bt _ 4摻雜低熔點的cuo能降低樣品的燒結溫度，沒有其他相生成，燒結后cuo以無定形態的形式存在，導致樣品介電性能降低。
  4. Color - painting is of two sorts : overglaze painting and underglaze painting. overglaze painting, with five - colored painting or fencai as its example, is to outline patterns with zhuming pigment and to fill them with various colors on the already glazed surface of the porcelain, before it is placed into a closed oven for a further baking at a compar - atively low temperature from 700 to 800c. underglaze painting is to paint with qinghua, underglaze red and other pigments on the body before it is glazed. its feature is that all the colors are under the glaze formed at high temperature and thus will never fade away

    釉上彩如五彩粉彩等，是在已燒成瓷的釉面上描繪紋樣填彩，再入紅爐以低溫燒烘，溫度約700 - 800度。此外，燒窯前即在坯體素胎上繪畫，如青花釉里紅等，則稱為釉下彩，其特點是彩在高溫釉下，永不退色。
  5. But the grain growth, grain semiconduction and grain boundary insulation were influenced by many factors, such as the type and contents of dopants, sintering temperature and so on. therefore, in this thesis the effect of the restore sintering temperature, the oxygenize temperature, the donor and acceptor dopant on the dielectric and varistor properties of devices were studied. with sem, the microstructure of srtio3 - based double function ceramic was analyzed

    而晶粒生長、晶粒半導化和晶界絕緣化受到多種因素的影響，諸如雜質的種類和含量、燒成溫度等，因此本論文研究了還原燒成溫度、中溫氧化溫度、施主和受主摻雜等對srtio _ 3基陶瓷的壓敏和介電性能的影響，並藉助于sem分析對srtio _ 3基雙功能陶瓷的微觀結構進行了分析。
  6. The studies indicate that different content of pyrophyllite and dolomite can cause the following three cases : ( 1 ) making the refractory point decrease linearly and, to some extent, influencing the microstructure and properties of sintered body ; ( 2 ) acceleratingmullite formation during sintering, reducing thermal expansion coefficient of bond, reinforcing the matching nature and improving the flexural strength and shock strength ; ( 3 ) preventing sic grinding tool from generating black core, expanding suitable sintering temperature range of sic grinding tool

    同時，也不同程度地影響了磨具燒結體的微觀結構和性能； （ 2 ）可促進在燒結過程中莫來石的形成，降低結合劑的熱膨脹系數，加強了結合劑與磨料的匹配性，提高了磨具的抗折強度和抗沖擊強度； （ 3 ）在一定溫度范圍內還可防止碳化硅磨具出現黑心現象，拓寬了碳化硅磨具的燒結溫度適應范圍。
  7. For the ceramic materials, the effects of additives such as pbo, b2o3, co2o3, mno2, cr2o3, sb2o3 on the electrical properties of bismuth - free zno - glass varistor were studied. the glass phase formed mainly by pbo and b2o3 during sintering process could decrease the sintering temperature, improve grain uniform growth and inhibit grain second growth. nonlinear property could be improved by properly adding co2o3, mno2, and cr2o3

    對瓷料而言，系統研究了非bi系zno -玻璃料配方體系中pbo 、 b2o3 、 co2o3 、 mno2 、 cr2o3 、 sb2o3等添加劑對壓敏電阻電性能的影響規律，其中， pbo 、 b2o3在燒結過程中形成的玻璃相，可降低燒結溫度，促進晶粒均勻生長，抑制晶粒二次長大， co2o3 、 mno2 、 cr2o3做為非線性添加劑，適量添加可提高樣品的非線性， sb2o3做為改性添加劑，在燒結過程形成的尖晶石相可細化晶粒，抑制晶粒二次生長，改善樣品的綜合電性能。
  8. The calculation method of the enamel glaze baking temperature

    搪瓷燒成溫度計算方法
  9. When sufficient wollastonite is added to ceramic material, the baking temperature can be decreased ang the baking duation greatly shortened to one rapid low temperature bake, thus saving fuel and reduing production costs

    在陶瓷原料中加入適量的硅灰石，可以大幅度降低燒成溫度，縮短燒成時間，實現低溫快速一次燒成，大量的節約燃料，明顯降低產品成本。
  10. The influence of burning system on the properties and structure of the ceramic capacitors has been studied under the certain temperature system, the optimum sintering temperature of the ceramics was primarily decided by the content of bi2o3 ? 3tio2. the sintering temperature dropped with the adding of bi2o3 ? 3tio2. at the range of suitable sintering temperature, slow heating and low temperature sintering can obtain fine grain and dense structure. it results in the improving of the breakdown voltage for the middle - high voltage ceramic capacitors

    研究了燒成工藝制度對電容器陶瓷性能和結構的影響，結果表明：在一定的升溫保溫時間下，瓷料的最佳燒結溫度主要取決于組成中bi _ 2o _ 3 ? 3tio _ 2的含量， bi _ 2o _ 3 ? 3tio _ 2含量的增加將降低燒結溫度；在合理的燒結溫度范圍內，慢速升溫和低溫燒結將有利於得到細晶緻密結構，從而改善中高壓陶瓷電容器的耐壓強度。
  11. After the sample is turned out, its internal and external structures are observed and its bulk density is measured in order to determine how the sintering temperature, the time of thermal preservation, and the quantity of admixture affect the performance of lytag

    通過對試樣內、外部結構觀察和容重的測定，研究燒成溫度、保溫時間及外加劑摻量對粉煤灰陶粒性能的影響。
  12. The preparation of metal - supported mullite and zro2 / batio3 ceramic membranes was studied. the influences of ceramic composition, sintering temperature and carbon content on the properties of ceramic materials ( porosity, pore diameter and strength, etc. ) were investigated. alkali corrosion resistance and electrolytic experiment results of these ceramic membranes were compared to those of asbestos and al2o3 porous ceramic membranes

    研究金屬支撐平板陶瓷膜的制備工藝技術，陶瓷膜的組成、燒成溫度、碳含量對材料性能（孔隙率、孔徑、強度等）的影響，比較幾種材料的陶瓷隔膜堿蝕量與電解實驗結果。
  13. The parameters of impregnation are as follows : ph is about 3, the range of temperature is from 20 to 45, and the time is about 2 to 6 hours. after the necessary treatments, zirconia cloths had the optimal strength when the diameters of zirconia fibers were controlled in 4um to 7um, and the sizes of zirconia grains were in 50nm to 100nm. the affec - ting factors were discussed and the liner regression analysis of the cloths was made, from w hich they show that the diameters and grain sizes have the significant influences on zirconia cloths. the obtained zirconia cloths have been accepted for use in nickel - hydrogen batteries by practical use

    研究結果表明：粘膠類纖維布最適合制備氧化鋯纖維布的前軀體；鋯液濃度以飽和溶液為宜；浸漬工藝參數為ph值3左右，溫度20 45 ，時間2 6小時；多餘鋯鹽的去除、浸鋯液后纖維布的整平處理及平燒施應力燒成有利於氧化鋯纖維布的柔軟及平整; 200 600燒成溫度段應緩慢燒成，控制氧化鋯纖維直徑在4 7 m ，氧化鋯晶粒尺寸50 100nm時氧化鋯纖維布的強度最好。
  14. The range of firing temperature of ceramic tube after dipping changed from 450 c to 1000 c. the above four slurries were also respectively favorable combination with al2o3 ceramic tube, and the range of firing temperature of ceramic tube after dipping slurry varied from 1 000 c to 1400 c

    鍍膜的陶瓷管燒成溫度范圍為450 1000 。前述的四種料漿也能良好地與al _ 2o _ 3陶瓷管結合，塗覆料漿的al _ 2o _ 3陶瓷管燒成溫度為1000 1400 。
  15. The experiment showed that the temperatures and the fiber proportions influenced great on the compressive strength, bending strength, volume density and the porosity of the composites

    實驗結果表明，燒成溫度和纖維含量對復合材料的耐壓強度、抗折強度、體積密度和氣孔率影響較大。
  16. Mechanical properties were tested and the influence of particle size, sintering temperature, and fiber content on property of the material was studied by the means of x - ray diffraction, om and sem

    測試了試樣的物理性能和力學性能，通過x衍射、 om及sem ，討論了纖維含量、燒成溫度、原料粒度對材料性能的影響。
  17. In this paper, sral2o4 : eu2 +, dy3 + phosphor with good photoluminescence properties was synthesized successfully through sol - gel method. be compared with conventional solid state method, the reaction temperature can be greatly decreased

    該方法較傳統的固相反應法明顯、有效的降低了反應燒成溫度，且產品具有粒徑小而均勻的優點。
  18. It was found that there was a close relationship between the adhesion strength of the bg coating and the surface roughness of the titanium alloy and the firing temperature. the chemical state of the elements ti and si at the coating interface varied. the chemical bond and the mechanical occluding make the bg coating form a strong adhesion with the titanium alloy

    通過研究發現， bg塗層與基體的結合強度與基體表面的粗糙度以及燒成溫度密切相關，塗層界面處ti元素和si元素的化學狀態發生了變化， bg與基體強結合的機制為化學鍵和機械嵌合兩種力共同作用。
  19. In the process of making 95 alumina ceramics, selected five kinds of alumina powder and studied the influence of different alumina powder on the sintering properties and mechanic properties of 95 alumina ceramics, moreover, selected the most agreeable alumina powder according to the apparatus for granularity analysis and scanning electron microscope ( sem ). the influence of different sintering temperature on the sintering mechanic properties, the microstructure of 95 alumina ceramics were investigated by adding y2o3 and la2o3 as two kinds of rare earth additives in alumina ceramics. the results indicated that the additive of la2o3 could improve the properties of 95 alumina ceramics more effectively and could get fine grain and tabular alumina that can enhance the strength of the material

    選用了五種al2o3粉料，研究了其對95al2o3瓷燒結性能和力學性能的影響，並結合粒度分析儀sem對al2o3粉料進行優選；通過添加y2o3 、 la2o3兩種稀土添加劑，研究了不同燒成溫度對95al2o3瓷的燒結性能、力學性能及顯微結構等的影響，結果表明：添加la2o3可以有效提高95氧化鋁瓷燒結性能和力學性能，形成細晶和板狀氧化鋁瓷的顯微結構；通過對比不同氧化鋁粉料制備氧化鋁瓷燒成溫度曲線與燒結性能的關系，確定最佳的燒成溫度范圍為1570 ~ 1600 。
  20. At the same sintering temperature, when the alumina fiber accounted for 10 %, the porosity of the composites was the lowest, the volume density was the biggest, and the compressive strength and the bending strength were the highest. when the sintering temperature was 1550 c, the compressive strength which could reach 332. 78 mpa, was the biggest ; when the sintering temperature was 1550 c, the bending strength which could reach 44. 04 mpa, was the biggest

    在同一燒成溫度下，氧化鋁纖維含量為10時，復合材料的氣孔率最低，體積密度最大，耐壓強度和抗折強度最高；燒成溫度在1550時，復合材料的耐壓強度最高，達到332 . 78mpa ，在1500時，復合材料的抗折強度最高，達到44 . 04mpa 。
分享友人
分享到 Line

分享到臉書