疲勞強度 的英文怎麼說

中文拼音 [píláoqiángdù]
疲勞強度 英文
cyclic strength
  • 疲 : 形容詞（疲乏; 勞累） tired; weary; exhausted
  • 勞 : Ⅰ動詞1 （勞動） work; labour 2 （煩勞） put sb to the trouble of; trouble sb with sth : 勞您費心...
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 疲勞 : 1. （疲乏勞累） tired; fatigued; weary; become fagged 2. （機能或反應能力減弱） fatigue; strain 3. [物理學] fatigue
  1. However, a low fatigue strength detail or a large built-in defect may produce only a single significant crack.

    但是，疲勞強度較低的細節部分或較大的內部缺陷可能只產生一條很大的裂紋。
  2. Tf _ the allowed torque according to tired intensity in changeful load

    在交變負荷下按疲勞強度所允許的轉矩。
  3. Fatigue assessment of longitudinal stiffeners of 8530teu container ship

    集裝箱船縱骨疲勞強度評估
  4. The fatigue behavior of strength, stiffness, and deformation of concrete is analysed systematically. the fatigue equation is established. the empirical expressions of the total longitudinal strain and the elastic modulus are given, and the relationships between the increasing rate of the total second - stage strain and the decreasing rate of the elastic modulus with the cyclic number are obtained

    系統地分析了砼抗拉、拉-壓疲勞強度、剛度、變形規律；建立了相應的s - n關系，提出了縱向總應變、彈性模量的經驗公式，及其第二階段總應變增長率、彈性模量衰減率分別與疲勞壽命的關系式。
  5. Reliability analysis of contact fatigue strength of cycloid gear in fa reducer

    傳動擺線輪齒面接觸疲勞強度可靠性分析
  6. A layer of hot-dipped galvanizing causes a considerable reduction in the fatigue strength.

    熱浸鍍鋅層引起疲勞強度的顯著降低。
  7. Results show that in the middle life range the fatigue strength of interference - fit riveting increases by about 25 % compared with that of conventional riveting

    研究結果表明：在中壽命區，干涉配合鉚接的疲勞強度比普通鉚接的疲勞強度提高約25 % 。
  8. Based on the aircraft structure fatigue theory, the article discussed the theoretical basis of methods that are usually used for aircraft structure fatigue crack - forming life estimation, i. e. the stress severity factor approach ( normal stress approach ), the local stress & strain approach, detail fatigue rating approach ( dfr ). also the processes of life estimation of these approaches are studied in the article

    文章在簡要介紹飛機結構疲勞強度理論的基礎上，對目前飛機結構勞疲勞裂紋形成壽命估算常用的應力嚴重系數法（名義應力法） ，局部應力應變法，細節疲勞額定值dfr法的理論依據作了較詳細的論述，同時對這些估算方法進行壽命估算的過程與步驟也作了詳盡的闡述。
  9. 4. the choice reference of medium belt material is came up with : with higher compress intensity, pull intensity and bend fatigue intensity, with middle or low elastic modulus, besides fine heat - resistant, wearable, oil - fast, water - fast anti - impactive capabilities

    4 、提出並分析了介質帶材料的合理選擇原則：壓縮強度、拉伸強度和彎曲疲勞強度高和韌性好的中低彈性模量復合材料，此外還需具有良好的耐熱、耐油耐水性、耐磨性、抗沖擊性、耐候性等。
  10. After being improved, the gear surface contact fatigue strength obeys weibull distribution and stress obeys normal distribution, the gear bottom bend fatigue strength and stress obey logarithm normal distribution, according to the relation of average safe rate and reliability, then the gear strength reliability design and check equations can be deduced

    將齒面接觸疲勞強度按威布爾分佈、應力按正態分佈處理，將齒根彎曲疲勞強度和應力均按對數正態分佈處理，再根據平均安全系數和可靠度之間的關系，推導出了齒輪強度可靠性設計和校核公式。
  11. By means of area method and stress field intensity approach and computational analysis of finite element, the fatigue strength of misaligned welded joint, " t " type of plate welded joint and cruciform joint are estimated. estimations are consistent with fatigue testes

    利用面積法和應力場強法，通過有限元計算分析，預測了錯位板接頭、 t型板接頭和十字型板接頭在對稱循環和非對稱循環時的疲勞強度，並與疲勞試驗進行了比較，理論預測與試驗基本一致。
  12. The fatigue alternating stress, which are highly variable in time, subject the crankshaft to very high and complex loading that induced to fatigue breakdown. the crankshaft design and manufacture must therefore precise calculations of the fatigue characteristics

    柴油機球鐵曲軸在工藝性和成本上佔有一定的優勢，通過滾壓強化工藝，疲勞強度有很大程度的提高，因而在國外得到廣泛應用。
  13. Among the results of these researches, cylindrical gears with curvilinear tooth trace have merits as follows : higher bending stress, low noise, better lubrication conditions, and no thrust forces. so this kind of gear can be considered to substitute the helical gear and herringbones

    本文提出的弧齒線圓柱齒輪是一種新型齒輪傳動形式，具有傳動平穩、噪聲低、潤滑性能良好、輪齒彎曲疲勞強度大的特點，因此該齒輪可以作為斜齒輪和人字齒輪的替代品用於高速重載場合。
  14. Based on the experimental data of rotor steel 1crmov in the loading of low - cycle fatigue at high temperature, the strength behavior and the fatigue life curve of this material at 550 have been achieved. meanwhile, with respect to three kinds of notched bar, their material damage assessment method under multiaxial stress condition is discussed

    本文在1crmov材料的高溫低周疲勞實驗數據進行了整理和統計的基礎上，得到了材料的疲勞強度特性曲線和疲勞壽命曲線，同時對三種不同缺口形式的圓柱形試件進行了多軸應力狀態下的材料損傷的研究，並通過數值計算方法進行了疲勞壽命評估。
  15. This paper analyses the engineering feasibility of using the static fem in the fatigue strength design of the shipunloaders structure through discussing the difference of infinite fatigue life design and finite fatigue life design and puts forward the calculating work cycle of this structure after considering the shipunloaders work process. it is useful for crane design - engineer to introduce the general fatigue strength design processes of the shipunloaders

    分析了有限壽命疲勞設計和無限疲勞壽命設計的異同，研究了用靜力學的有限元法進行結構的疲勞強度設計的技術可行性問題；並結合裝卸橋的工作過程，提出了相應的計算工作循環；介紹了裝卸橋疲勞設計的一般步驟
  16. Thermoplastics valves - fatigue strength - test method

    熱塑性塑料閥門.疲勞強度.試驗方法
  17. En 28659 thermoplastics valves. fatigue strength. test method

    熱塑料制閥門.疲勞強度.試驗方法
  18. Standard of test method for surface load capacity of gears

    齒輪接觸疲勞強度試驗方法
  19. Standard of test methed for bending load capacity of gears

    齒輪彎曲疲勞強度試驗方法
  20. The fatigue strength analysis of the rotor of defective generator

    帶缺陷發電機轉子疲勞強度分析
分享友人
分享到 Line

分享到臉書