疲勞誤差 的英文怎麼說

中文拼音 [píláowùchā]
疲勞誤差 英文
fatigue error
  • 疲 : 形容詞（疲乏; 勞累） tired; weary; exhausted
  • 勞 : Ⅰ動詞1 （勞動） work; labour 2 （煩勞） put sb to the trouble of; trouble sb with sth : 勞您費心...
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 疲勞 : 1. （疲乏勞累） tired; fatigued; weary; become fagged 2. （機能或反應能力減弱） fatigue; strain 3. [物理學] fatigue
  • 誤差 : error
  1. For rotor steel ( 30crlmolv steel ), the tests of low - cycle fatigue property are done under different temperatures. the fatigue life under different temperatures is researched to make up for the defects of the testing for foreign similar materials. when pull - stretch data is attempted to evaluate low - cycle fatigue data, the result shows that four - point associated method in middle - low life zone is done well under room temperature, but there are large errors of four - point associated method and general - slope method under other temperatures

    在本文中，通過與國外同類材料的性能進行比較，國產材料與國外材料共有的材料特徵基本相同；對轉子鋼（ 30crlmolv鋼）進行了不同溫度下的低周疲勞性能實驗，研究其在不同溫度下疲勞壽命，以彌補國外對同類鋼材測試的不足；採用拉伸數據預測低周疲勞壽命時發現，室溫條件下用四點關聯法在中低壽命區預測較好，在高溫條件下四點關聯法和通用斜率法都有較大誤差，需要進行改進。
  2. The existed material fatigue performance test curves are dealt with and analyzed, and the non - dimensional stress - strain curve, tangent modulus factor curve and fatigue life curve are drawn based on the experiment data, and these three non - dimensional parameter curves are used to find the inherent rules that the test curves can be replaced each other to some extent. it can be concluded that if the common character and system error of these materials are found, the test curve of a certain material can be used for reference by another material. this is a simple approach about fatigue life estimate and is engineering practical

    對已有的材料力學疲勞性能試驗曲線進行分析整理，利用試驗數據繪制了相對應力應變曲線、切線模量因子曲線和疲勞壽命曲線，利用這三種無量綱參數曲線發現了其中存在的規律性，即在某種程度上實驗曲線可以互相取代，並用試驗數據對此進行了討論，並由此推斷，如果找出材料彼此的共性或彼此之間的系統誤差就可以將一種材料的試驗曲線供其它材料參考使用，這是一種估算材料的疲勞壽命的簡便方法，對工程而言具有實用性。
  3. With metal fatigue in material mechanics, this paper deduces the limestone fatigue curve of longmen grottoes by means of marble s one within the error permission. by the experiment elects the crucial factors of current vibration environment in longmen grottoes, the author contrasts the result of the experiment with its fatigue curve referred above and analyses the fatigue effect of longmen grottoes. finally, it is pointed out that after longmen grottoes have being suffered weathering and water - erosion more than 1500 years, the vibration environment is becoming an crucial factor leads to fatigue effect, especially in those weak surface carvings just like the crossings of several rifts, serious weathering places, etc

    借鑒材料力學中金屬疲勞破壞的研究手段，在誤差允許范圍內用大理巖疲勞曲線推導出門石窟石灰巖疲勞曲線。通過對石窟實際振動環境中典型要素的抽取和振動試驗，將試驗結果與疲勞曲線進行對比，分析了門石窟的疲勞破壞效應。文章指出，在經歷了1500多年的風化和流水溶蝕后，振動環境已成為導致門石窟某些薄弱點如多條裂隙交叉點嚴重風化酥解的壁面雕刻品等產生疲勞破壞的重要誘發因素。
  4. The full - coupled method developed with damage mechanics and the finite element analysis is performed on calculation of fatigue damage accumulation of the critical welded components in the tsing ma bridge

    這種偏於安全的誤差，用於結構的疲勞設計是合適的，但對于在役結構疲勞損傷累積的準確評估卻是不利的。
  5. Traditionally, the gauge is recognized by human eyes. however, some of the subjective factors such as : observation angle, observation distance and fatigue may have effects on the value

    這種判別方法受人的主觀因素如人的觀測角度，觀測距離及疲勞強度等影響，誤差很大，可靠性不高。
  6. ( 1 ) from the considering of the probabilistic model being actually established by randomness of the average relations fitting into the test data, the appropriated statistical distributions for the fatigue lives are explored by the errors, which is different from the commonsense

    （ 1 ）概率s - n曲線本質上是在最佳擬合曲線（即均值s - n曲線）的基礎上，考慮誤差的隨機性建立的。本文首次從誤差數據的角度研究了疲勞壽命的良好假設分佈模型。
  7. According to the analysis and testing of driver fatigue, it can be found that driver ' s behavior deteriorates generally. that is, vision, audition and estimate are all debased. further, driver ' s reaction time is prolonged and operation failure is increased

    通過對駕駛疲勞的內因分析和實驗測試，結果表明駕駛員在疲勞狀態下表現變差，體現為視力、聽力水平降低、速度判斷能力降低、反應時延長、注意品質下降、操作失誤增多。
  8. Three advanced issues are studied. they are the statistical distributions for the errors of the average s - n relation fitting into the test data, the maximum value model for the probabilistic model, and the material probabilistic fatigue strength under spectrum - loads

    論文圍繞均值s - n曲線擬合s - n數據誤差的統計分佈模型、測定概率s - n曲線的極大值模型和基於極大值模型的譜載荷下材料的概率疲勞強度的測定三方面，開展了較為深入地研究。
  9. These rules consist of the total fit, the mathematics and fatigue physics, and the safety in tail predictions. an analysis of the test s - n data of 16mn steel weld joints reveals that the four models are reasonable if only considering the total fit as the conventional method did. but if by the present three rules, the appropriate models should be the normal or the extreme maximum value

    根據先前提出的有限數據下良好假設分佈的確定方法，包括三個原則，即假設分佈形狀與誤差數據真實分佈形狀的一致性、預測的總體擬合效果、與疲勞失效機制的一致性和尾部預測的安全性，通過對線性均值s - n曲線擬合16mn鋼焊接頭s - n數據誤差的統計分析，說明應用一般推斷方法， 4種分佈都可合理地作為數據的統計模型，綜合考慮三原則后，極大值和正態分佈是可能的良好假設分佈。
  10. He consulted me because of his nasal allergy symptoms, including stuffy nose and sneezing in the morning, fatigue and listlessness, and despite the treatment of western medicine, he still had many problems, such as poor learning ability, concentration problems, lack of persistence, repeating mistakes, rough behavior, anxiety and impatience

    來中醫門診之主訴為:鼻過敏，晨起鼻塞.打噴嚏，容易疲勞，總是無精打采，雖然經過西醫治療，但其學習能力仍然很差，上課時注意力無法集中，經常會失神.心不在焉，一件事情未完成，就會失去興趣，經常犯同一種錯誤;他感覺他很粗魯，作事情時經常因動作太大而搞的一團亂，焦躁不耐煩
  11. We can see bilinear behavior from the relation - ?. diagram of fatigue life and total cyclic hysteresis energy as well as the fatigue life and half - life cyclic hysteresis energy. the divergent points both reside at the strain amplitude of 0

    根據合金的循環硬化和軟化行為，採用分段累積的方法計算材料的總滯?能比直接用半壽命滯?能乘以循環數得到的結果更符合實測值，而用疲勞特性參數計算總滯?能誤差較大。
  12. Moreover, the influence factors of stress ratio, intermittent time, loading order etc. to fatigue strength were discussed

    另外，本文詳細分析了、加載順序、間歇時間、加工缺陷和安裝誤差等因素對疲勞強度的影響。
分享友人
分享到 Line

分享到臉書