真平均溫度 的英文怎麼說

中文拼音 [zhēnpíngjūnwēndù]
真平均溫度 英文
true mean temperature
  • 真 : Ⅰ形容詞（真實） true; genuine; real Ⅱ副詞1 （的確; 實在） really; truly; indeed 2 （清楚確實） cl...
  • 平 : Ⅰ形容詞1 （沒有高低凹凸 不頃斜） flat; level; even; smooth 2 （高度相同; 不相上下） on the same l...
  • 均 : Ⅰ形容詞（均勻） equal; even Ⅱ副詞（都; 全） without exception; all
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 溫度 : [物理學] temperature
  1. The main results are : grinding is favorable to improve surface smooth degree, while nitrided and slow deposition makes sic granules fine ; the width of coatings gap increased in order of grinding, nitrided and vacuum heat treatment, but gap defects in multilayer coatings could be removed by slow deposition ; temperature of maximum weight loss could be decrease to 600 by grinding, vacuum heat treatment or slow deposition, but it will increased to 800 after nitrided ; oxidation kinetics curves all varied with the coating modifications

    主要有：磨削改性有利於提高塗層表面平整度，氮化和慢沉積使塗層表面顆粒細化。塗層間隙寬度按磨削改性、高溫氮化、真空熱處理依次增大，而慢沉積可獲得無面缺陷的多層塗層。磨削改性、真空熱處理及慢沉積均使最大氧化失重溫度點提前至600 ，而高溫氮化則使最大失重點后移至800 。
  2. Results of vmd experiments indicate that flux increases when feed temperature, feed rate and vacuum degree increase. but the increase of flux becomes slowly when feed rate reaches 60l. h - 1 ; flux increases with pore size rapidly, but rejection approaches zero when pore size reaches 0. 5m

    實驗表明，隨進料溫度、進料流速、冷側真空度的增大，膜通量增大；但進料流速增大到60l . h - 1之後，通量隨進料流速的增長變緩；膜通量隨孔徑較快地增大，但當膜平均孔徑達到0 . 5m時，截留率迅速降低，已無實際意義。
  3. In this paper, firstly, monolithic materials cosb3 and bi2te3 were prepared by sparkle plasma sintering ( sps ) respectively, and at the same time the microstructure of cosb3 and bi2te3 were studied by sem ; the seebeck coefficients and electrical conductivities of monolithic materials were measured by standard - four - probe method ( ulvac zem - 700 ) in a he atmosphere simultaneously, and their thermal conductivities were investigated by laser flash method ( tc - 7000 ) in vacuum. secondly, the junction temperature of graded bi2te3 / cosb3 thermoelectric materials was optimized based on the thermoelectric transport properties of monolithic materials, also when graded materials were used in the temperature difference ranging from 300k to 800k, the length ratio of monolithic materials cosb3 and bi2te3 were optimized in theory. thirdly, graded bi2te3 / cosb3 thermoelectric materials were prepared by two - step sps sintering, and the relationship between its average seebeck coefficients and temperature were calculated by theory mo del

    均質材料cosb _ 3和bi _ 2te _ 3的電導率和seebeck系數採用標準四端子法于he氣氛下在zem - 1上同時進行測量；熱導率採用激光微擾法（ tc - 7000 ）于真空狀態下進行測量；其次，在對均質材料cosb _ 3和bi _ 2te _ 3熱電傳輸特性研究的基礎上，對結構梯度bi _ 2te _ 3 cosb _ 3熱電材料的界面溫度進行了優化；為了使結構梯度bi _ 2te _ 3 cosb _ 3熱電材料在300k至800k的溫度范圍內具有最佳的熱電性能，本研究同時對梯度結構熱電材料當中均質材料cosb _ 3和bi _ 2te _ 3材料的長度進行了優化設計；第三，通過兩步放電等離子燒結的方法制備出了結構梯度bi _ 2te _ 3 cosb _ 3熱電材料；採用理論計算的方法研究了梯度結構熱電材料平均seebeck系數和溫度的關系；同時為了驗證設計的結果，本論文對結構梯度bi _ 2te _ 3 cosb _ 3熱電材料的開路輸出電壓和熱端溫度之間的關系及梯度材料在300k至800k的溫度范圍內使用時的功率輸出進行了相應的研究。
  4. Calculating the distribution of losses in stator strands based on the eddy current distribution coefficient method. it shows that results from this method and the traditional method are nearly same. so, the average method can be applied to calculate the temperature field

    研究結果表明，採用渦流分佈系數法和傳統所採用平均法計算損耗進而得到的溫度場真實分佈基本相同，可在工程中採用更為簡便的渦流平均法計算損耗和溫度場。
分享友人
分享到 Line

分享到臉書