研磨用磨塊 的英文怎麼說
中文拼音 [yánmóyòngmókuāi]
研磨用磨塊
英文
emery cake- 研 : 研同 「硯」
- 磨 : 磨動詞1 (摩擦) rub; wear 2 (研磨) grind; mull; polish 3 (折磨) grind down; wear down [out]:...
- 用 : Ⅰ動詞1 (使用) use; employ; apply 2 (多用於否定: 需要) need 3 (敬辭: 吃; 喝) eat; drink Ⅱ名...
- 塊 : 名詞(古時佩帶的玉器) penannular jade ring (worn as an ornament in ancient china)
- 研磨 : 1. (用工具研成粉末) grind; pestle2. (用磨料摩擦器物使變得光潔) abrade; polish
-
Aim of this study was to meet the need for development of tribological parts in pumps. at room temperature tribological properties of different sliding pairs of silicon carbide and alumina - based ceramics were tested using a laboratory tribometer in the ring - on - plate geometry under reciprocating sliding linear contact in different media, such as distilled water, aggressive media and air
本文針對目前泵用摩擦零部件材料發展的需要,在實驗室摩擦磨損試驗機上研究了按環/塊線接觸方式作往復運動條件下的碳化硅和氧化鋁基陶瓷材料摩擦副在水、化學腐蝕性介質作潤滑劑和無潤滑時室溫下的摩擦磨損特性。On the other side, based on research on noncircular surface grinding features, this deissertation designs the data structure of simulation driver, then, applies interpolation theory to design the grinding motion simulation module and researches all sorts of cases on constructing the solid swept of grinding wheels in the process of noncircular surfaces grinding, finally, designs nc codes verification simulation module by using design model - based verification technique
在實體模擬技術方面,詳細研究了非圓曲面磨削加工的特徵並設計了對應的模擬驅動數據結構;應用插補原理設計了體現加工速度的運動過程模擬模塊;詳細研究了非圓曲面磨削加工中砂輪的相對和絕對運動掃掠實體的構造,並採用基於精確實體設計模型的驗證方法構建了數控代碼的模擬驗證模塊。The friction and wear behavior of the nanocomposites sliding against aisi - 1045 steel under water - lubricated condition and dry condition was examined on an m - 200 test rig in a ring - on - block configuration
採用m - 200型環-塊摩擦磨損試驗機研究了復合材料在水潤滑與干摩擦條件下的摩擦磨損行為,對摩材料為45 ~ #鋼。The iron covered silicon powder was fabricated separately by the milling method and the mixing method. treated separately at 500, 600, 700, 800, 900 and 1000 for 1 minute, the iron silicon alloy bulk was attained. it also found that the density of the bulk was enhanced by the boost of the treated temperature
實驗分別採用球磨法和混料法制備鐵硅包覆粉末,採用放電等離子燒結技術分別在500 , 600 , 700 , 800 , 900 , 1000保溫一分鐘進行處理,得到鐵硅合金塊體,研究發現,隨著處理溫度的提高,塊體的緻密度隨之增加,顯微結構的分析表明,塊體基本保持了包覆粉末原始自然狀態。3. the diamond segment wear process was analyzed by testing the weight of segment before and after sawing. the patterns of wear and breakage of diamond grits and bond wear mechanism of the blade were analyzed based on the observation on the working surface of the saw blade by stereo microscope and scanning electronic microscope
採用稱重法測量鋸切過程鋸片節塊磨損量,並通過計算磨削比,分析了混凝土鋸切過程金剛石節塊的磨損特性及其影響因素,並採用sem和體視顯微鏡觀察節塊不同部位工作表面和金剛石的磨損破壞情況,研究了金剛石磨損破壞的主要形式和胎體材料的磨損形態。The diamond indenter is a king of standard measuring tool used to determine the standardized blocks and verify and calibrate schelometers. it is made by welding, grinding and machining certain grain of quality natural diamond into the rockwell, vickers of brinell hardness
金剛石壓頭是將一粒定量的優質天然金剛石,按要求鑲焊研磨再機械加工成洛氏、維氏和布氏的標準計量工具,主要用於硬度塊的定度和對硬度計的鑒定。High technology segmented blades manufactured by patented process low cost excellent for general purpose fast cutting long life good for brick, block, stone, concrete, and tile use wet or dry
採用高新科技研製而成的節塊式鋸片,磨削速度快,使用時間長可在干、濕環境下磨削磚塊、石材、混凝土陶瓷等。The fine turning function can adjust center accurately. using the fixing block and folding down the screw when mouse much, can grind oval workpiece conveniently
左右大量移動時,可拆下微調螺桿。用固定塊定位,可方便研磨橢圓工件。At last the crank dieblock is taken as the study object, and the above two universe models are included. the joint wear between crank and frame, crank and connecting rod, connecting rod and dieblock is studied. the concrete arithmetic project is brought forward and the universe program written in the vb environment is supplied
最後以曲柄滑塊為研究對象,融入上述兩個通用模型,研究曲柄與機架,曲柄與連桿,連桿與滑塊三對摩擦副鉸接處的磨損,提出了具體的演算法方案並在visualbasic環境下編寫了通用程序。However, we cannot produce this pm insert at home up to now. so, we do this work to help the domestic production of pm rocker arm inserts in our country and reduce their costs
本課題旨在針對國內粉未冶金耐磨搖臂鑲塊的研製現狀,加快汽車用粉未搖臂鑲塊的國產化研究進程。分享友人