破損位置 的英文怎麼說

中文拼音 [pòsǔnwèizhì]
破損位置 英文
damage location
  • 破 : Ⅰ動詞1 （完整的東西受到損傷） be broken; be damaged 2 （使損壞） break; break down; damage 3 （使...
  • 損 : Ⅰ動詞1 （減少） decrease; lose 2 （損害） harm; damage 3 [方言] （用尖刻的話挖苦人） speak sarcas...
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 破損 : damaged; worn; torn; damage; failure; breakage
  1. In chapter 5, by number value simulation calculation and experiment of one simple support beam, we will compare the magnitude of the coupling static and dynamic stress at each point on the girder under harmonic excitation, and so find conclusions such as : ( 1 ) there are so much correlations between structure damage and environmental effect and exterior excitation leads dominant effects in structure damage that we should consider static and dynamic stress together. ( 2 ) new intension design rules should be set up, according which the range of structure possible damage position should be estimated in advance

    得到以下結論： （ 1 ）結構的破壞和環境的影響密不可分，外部激勵在結構破壞中發揮了重要的作用，應該將結構所受的靜力和動力一起考慮； （ 2 ）應該建立新的強度設計準則，並以此作為依據，對已知結構的可能損傷位置有預先的范圍估計，從而為損傷識別的準確定位提供理論依據。
  2. If the edge of the fabric was damaged already, see the size and the position of the damaged place, the best method is to trim them, then hide them, not repair them

    如果織物的邊緣已經破損了，要看破損地方的大小和位置，最好的方法是把它們剪短，然後把他們藏起來，而不是修復它們。
  3. Basing on rc simple supported beam the study of the paper is modal analysis using the finite unit software ansys, and the relationship among the transformation of vibration frequency, value of attached load, position of attached load, degree of damage, position of damage is discussed

    本文利用大型有限元軟體ansys針對工程常用的鋼筋混凝土梁橋進行了模態分析，討論了振動頻率的變化與附加荷載大小、附加荷載位置、破損程度、破損位置之間的關系，研究了混凝土梁橋從完整階段到破壞階段振動頻率的變化規律。
  4. Considered local damage due to steels corrosion, fatigue, prestressing loses, whole bridge incline and distortion, this paper studies damage diagnosis technique of the cable - stayed bridge and determines the location and size of damages for yonghe cable - stayed bridge, which has been used after 15 years

    針對鋼筋腐蝕、疲勞、預應力鬆弛、橋梁整體傾斜或變形所引起的斜拉橋局部破損，本文以使用15年後的永和斜拉橋為研究對象，對大型斜拉橋破損診斷技術進行研究，對永和斜拉橋破損位置進行定位、對其破損程度進行評價。
  5. Morce can help enterprises to avoid the harm and the cost brought by core employee turnover, such as hindering the smooth operation of enterprise, causing the turnover of human capital with high quality, bringing about high cost of replacing post, making the characteristics of enterprise culture obscure, leading to the cost of intangible assets, damaging the core competitive capacity of enterprise. next, morce is the essential of human resources management and is helpful for increasing the efficiency of human resources management and improving its level. therefor, morce should have the most important place in human resources management

    核心員工流失對企業的危害和損失是多方面的，如影響企業正常運營、造成優質稀缺性人力資本流失、帶來高昂的職位重置成本、模糊企業文化的特色、導致無形資產損失、破壞企業核心競爭力等；其次，保留核心員工是企業人力資源管理的前提，有利於提高人資管理效益和全面提升人力資源管理水平，因而應將核心員工保留管理置於企業人力資源管理工作的首位；特別是在當代新的經濟環境下，企業對優質稀缺性人才的爭奪日趨激烈，保留核心員工顯得尤為重要。
  6. The compression experiment after impact is discussed in the paper. also, the compression damage force after different impact energy and the strain response of different position are presented. it is a satisfying method for experimental research to find the strain distributing in impact and cai, as well as the compression strength of cai

    同時本文還進行了沖擊后的壓縮試驗，對編織型復合材料在不同沖擊能量下的壓縮破壞載荷，及損傷后不同位置的響應進行了記錄和討論，是一個全面考察沖擊和沖擊后壓縮的應力分佈和研究破壞載荷及剩餘強度的較為滿意的實驗研究方法。
  7. Then the de - lay differential method of detecting the milling cutter breakage is put forward according to the above research work and the changing characteristics of power signal and vibration displacement signal when the tool breakage occurs, the monitoring stategy of sensors fusion based on the artificial neural network is put forward. the monitoring system of milling cutter breakage based on the information fusion of the power signal and vibration displace - ment signal has been developed. the diff culty in giving a dectecting threshold due to the changeable character of character of cutting condition has been solved, and a good reliability is ensured over a wide range of conditions

    在上述研究工作的基礎上，提出了基於人工神經網路用於多傳感器信息融合的監測策略，開發研製了以機床主電機功率信號和主軸振動位移信號特徵參量融合的銑刀破損監測實驗系統，解決了銑削過程中切削條件多變導致監測閾值難以設置的難題，保證了在較寬的工作范圍內具有較高的識別準確率。
分享友人
分享到 Line

分享到臉書