磨損性 的英文怎麼說

中文拼音 [mósǔnxìng]
磨損性 英文
abradability
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 損 : Ⅰ動詞1 （減少） decrease; lose 2 （損害） harm; damage 3 [方言] （用尖刻的話挖苦人） speak sarcas...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 磨損 : wear and tear; abrasive wear; abrase; abrade; detrition; wear; scuff; wear out; fray; battering; ...
  1. There have been attempts to modify the fiber chemically to resist abrasion enhancement.

    過去曾設法用化學變性方法，提高纖維的抗磨損性能。
  2. The fibers with moderate abrasion resistance include wool, cotton, and the high wet-modulus rayons.

    具有中等耐磨損性能的纖維有羊毛、棉花和高濕模量粘膠纖維。
  3. Frosting occurs when two fibers differing in both color and abrasion resistance are combined in a fabric.

    兩種顏色和耐磨損性能不同的纖維組合的織物也會出現霜花色。
  4. Footwear - test methods for insoles - abrasion resistance

    鞋靴.鞋墊試驗方法.耐磨損性
  5. Footwear - test methods for outsoles - abrasion resistance

    鞋靴.外底試驗方法.耐磨損性
  6. Effect of antifriction on friction and wear properties of resin - based composite

    減摩組元對樹脂基閘片摩擦磨損性能的影響
  7. The results show that adding certain quantity manganese to 28cr cast iron will maintain its better corrosion resistance and wear resistance, ever in the thick casing work piece

    結果表明，在28cr鑄鐵中加入適量的錳，可以使其保持較好的耐蝕性能和抗磨損性能，即使是在厚大斷面鑄件中。
  8. Influence of 19cn5 and 20crmnmo sulfurized after cementite on anti - freting performance

    鋼滲碳后硫化對摩擦磨損性能的影響
  9. Wear properties of nano tin modified cermet cutters

    改性金屬陶瓷刀具的磨損性能研究
  10. Frictional behavior is modified by colloidal silica or starch deposition.

    耐磨損性能可以通過在織物上沉澱膠狀硅或澱粉一類物質而得到改善。
  11. In this dissertation, al - si / sicp composites brake rotor with diameter of 1200mm was firstly fabricated by a novel spray deposition technology, and simultaneously coupled brake pad was prepared by a novel dry - powder processing route, termed as two - step pressing process. a wedge pressing technology was developed to densify the as - produce al - si / sicp composite brake rotor

    本文首次採用噴射沉積技術制備了直徑達1200mm的al - si / sicp制動盤，同時採用二次壓制工藝制備出了配套的合成閘片，研究了制動盤的楔壓緻密化技術、機理，復合材料摩擦磨損性能及機理。
  12. Wear resistance of q235 steel surface mo - cr alloy layer by double glow discharge technology

    235鋼表面雙層輝光離子強化層摩擦磨損性能
  13. Effect of laser power on microstructures and wear properties of wcp ni metal ceramics coating

    基金屬陶瓷塗層的組織與磨損性能的影響
  14. Study on the wearable performance of carbon nanotube zinc alloy marix composites

    鋅基復合材料的磨損性能研究
  15. The age hardening characteristic of as - cast cu20ni20mn and cu20ni35mn alloys and the interface characteristic between the alloy and cast tungsten carbide were studied, and on the basis of this study, composites of cu - ni - mn alloy reinforced with different volume fraction ( 0 - 45vol. % ) and different size ( 42 - 362 m ) of cast tungsten carbide particles were made by vacuum hot - pressing liquid sintering technology. pin on disk two body abrasion tests have been performed with different size of sic abrasive under different loads

    本文研究了鑄態cu20ni20mn和cu20ni35mn合金的時效硬化特性及其與鑄造碳化鎢的界面特性，並在此基礎上以不同尺寸（ 42 362 m ）的鑄造碳化鎢顆粒為增強體，採用真空熱壓液相燒結技術制備了不同顆粒含量（ 0 45vol . ）的鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料；以不同粒度的sic為磨料，在不同載荷條件下利用銷?盤磨損試驗機測試了復合材料的二體磨料磨損性能。
  16. Abstract : in this paper, the surface of the ore milling roller was quenchedby the laser, so that increase its surface rigidity and improve its antiwear properties, and prolong its life

    文摘:應用激光束對磨輥表面進行淬火處理，提高磨輥表面硬度，增強磨輥的抗磨損性能，從而達到延壽的目的。
  17. When fillings is other materials ( unprocessed montmorillonite, powder coal ash, co - composite of powder coal ash and organo - montmorillonite, co - composite ofcarbonizing calcium and organo - montmorillonite ) in the binder and content of organo - montmorillonite in the binder is five percent decided by tensile - shear experiment, tensile - shear strength of binder is up to tiptop ; at the same time, this paper carries out abrasion experiment, and, by comparison, concludes abrasion property of coating is optimum when content of organo - montmorillonite in the binder coating is five percent, and observes abrasion sample under set

    當膠粘劑中填料為其它物質（未處理蒙脫土、粉煤灰、粉煤灰和有機化蒙脫土共復合、碳化鈣和有機化蒙脫土共復合）時，通過拉伸剪切試驗確定膠粘劑中有機化蒙脫土含量為5時，膠粘劑的拉伸剪切強度最高；同時進行了沖蝕磨損試驗，通過比較得出，當膠粘劑塗層中有機化蒙脫土含量達到5時，塗層的耐沖蝕磨損性能最佳，並對沖蝕磨損試樣在掃描電子顯微鏡（ set ）上進行觀察。
  18. Testing coated fabrics - method 16 - methods for determination of colour fastness to wet and dry rubbing and determination of resistance to printwear

    塗覆織物試驗.方法16 .濕摩擦和干摩擦色牢度及印花耐磨損性測定方法
  19. We also studied the dynamic characteristics of cf / cu ( c ) - cu composites, the results show that, by the method of graphite is coated with copper, the coefficient of friction and the wear rates remarkably decreased. with the increase of the copper coated carbon fiber content, the wear rates of cf / cu ( c ) - cu composites is notably decreased, while the coefficient of friction is increased. with the increase of electric current density, the wear rate of cf / cu ( c ) - cu composites is increased

    研究發現，碳纖維鍍銅石墨-銅復合材料的電摩擦磨損性能與碳纖維含量存在一最佳值，當碳纖維含量為0 . 6時，其電摩擦磨損性能最好；對于不同電流密度下的電磨損性能的比較可以發現，通電磨損時的電摩擦系數要小於機械磨損時的摩擦系數，碳纖維鍍銅石墨-銅復合材料的電摩擦系數隨電流密度增大先減小而後增大，在電流密度為15a cm ~ 2時達到最小值；通電磨損量要遠大於機械磨損量，且隨著電流密度增大，磨損量增加。
  20. Moreover, it is a compatible raw material under the terms of the food sanitation law. also, through the use of newly developed complex technology, we have given this coating excellent non - adhesion, low friction and sliding capabilities, etc. thanks to these capabilities it has become possible to adjust the surface treatment performance to match a wide range of application purposes, equipment, etc

    聚氨酯本身具有耐磨損性，高摩擦系數特性，還有防止靜電的導電特性，保證工廠安全的自動溶解特性，亦可用作食品衛生法對應的原料，此外通過最新開發的復合技術具備了無粘性，低摩擦性，光滑性等諸多優點，用途更廣泛，可適用於各種器械的表面處理施工。
分享友人
分享到 Line

分享到臉書