磨擦對象 的英文怎麼說

中文拼音 [mócāduìxiàng]
磨擦對象 英文
reibpartner companion friction surface friction partner
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 擦 : 動詞1 （摩擦） rub 2 （用布、 手巾等摩擦使干凈; 揩拭; 抹） wipe; scrub; clean 3 （塗抹; 搽） spre...
  • 對 : Ⅰ動詞1 （回答） answer; reply 2 （對待; 對付） treat; cope with; counter 3 （朝; 向; 面對） be tr...
  • 磨擦 : rub; abrade; abrase磨擦電 triboelectricity; 磨擦工 rubber; 磨擦劑 abrasive; 磨擦器 grater; rubber...
  1. In this paper, the microstructure changes of polypropylene induced by a complex combination of shearing, compression, stretching and friction actions during single pan - milling or co - milling with iron, uhmwpe and waste tire rubber chips ( wtr ) were studied and the stress induced effects were revealed. the structure and morphological development of iron particulates and wtr during pan - milling and co - milling with polypropylene were also characterized. the properties of pp / fe, pp / wtr and pp / wtr / fe composites prepared through pan - milling techniques were investigated

    本文利用磨盤型力化學反應器對被碾磨材料施加強大的剪切、環向應力、擠壓、拉伸和摩擦作用，研究聚丙烯碾磨和共碾磨粉碎過程微觀形態結構和性能的變化，以及聚合物在碾磨過程中呈現的力化學現象，並將其應用拓展至金屬、橡膠等體系，研究碾磨粉碎在聚丙烯鐵超微粉體的制備、高交聯密度彈性材料廢舊輪胎橡膠（ wtr ）的超微粉碎，以及pp fe ， pp wtr材料的性能與碾磨作用的關系。
  2. Summarizing and discussing the usual wear fault and wear kinds of the general mechanical equipment. engines of self - propelled gun are the main discussed targets, the component of the friction pairs and wear fault rules of which are analyzed. building the belter base for carrying out wear state monitoring further

    總結和討論了一般機械設備常見的磨損故障和磨損類型，並以自行火炮的發動機為重點研究對象，分析其主要摩擦副的材料組成和磨損失效規律，為進一步實施磨損狀態監測奠下良好的基礎，討論了自行火炮潤滑油變質原因和機理。
  3. At last the crank dieblock is taken as the study object, and the above two universe models are included. the joint wear between crank and frame, crank and connecting rod, connecting rod and dieblock is studied. the concrete arithmetic project is brought forward and the universe program written in the vb environment is supplied

    最後以曲柄滑塊為研究對象，融入上述兩個通用模型，研究曲柄與機架，曲柄與連桿，連桿與滑塊三對摩擦副鉸接處的磨損，提出了具體的演算法方案並在visualbasic環境下編寫了通用程序。
分享友人
分享到 Line

分享到臉書