等軸測圖 的英文怎麼說

中文拼音 [děngzhóucètú]
等軸測圖 英文
normal axomometric drawing
  • 等 : Ⅰ量詞1 （等級） class; grade; rank 2 （種; 類） kind; sort; type Ⅱ形容詞（程度或數量上相同） equa...
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 圖 : Ⅰ名詞1 （繪畫表現出的形象; 圖畫） picture; chart; drawing; map 2 （計劃） plan; scheme; attempt 3...
  1. We can get many physical parameters through indicator diagram acquired in the experiment. such as indicator work, mean indicated pressure, maximal pressure and corresponding crank angle, maximal rate of pressure rise and corresponding crank angle and mass fraction burned, heat release rate, etc. these physical parameters can analyze and show primary in - cylinder combustion process in engine

    通過實測的示功圖，經過計算整理可以獲得諸如指示功、平均指示壓力、最高燃燒壓力及其對應曲軸轉角、最高壓力升高率及其對應曲軸轉角、已燃質量分數、燃燒放熱率等物理量，可供進一步分析和揭示發動機缸內燃燒過程。
  2. Results the occlusion contact data and graph of wedge - shaped teeth defect had the features of trauma occlusion. 42. 97 % of them has the larger axial gradient degree, 96. 09 % of them has abration in different classes, 46. 29 % missing the front teeth and 57. 03 % missing the buccal teeth

    方法採用臨床物理檢查和石膏模型測量，確定楔狀缺損牙軸傾度、磨損指數、牙缺失等指標；採用計算機圖像處理技術，自行編制軟體程式及硬體系統，測試被檢光（牙合）片，分析並提取楔狀缺損牙接觸（牙合）力、面積、接觸點（牙合）應力等資料和圖形信息。
  3. It utilizes the computer digital image processing technology. and this system can measure the characteristic parameters automatically and quickly, such as luminous intensity, center of far light, corner of the close light. the advantage is high accuracy, good repetition and automatic measurement

    此系統採用多維精密可調工作臺，並利用計算機數字圖像處理技術，以vc + +編程實現，達到了自動測量出被測校準器的發光強度，遠光中心坐標，近光拐點坐標以及光軸偏角等特徵參數的目的。
  4. The second part of the dissertation concentrates on the applications of the digital image processing technique in measuring the specimen deformation in - triaxial test. it includes : ( 1 ) discuss of some problems in triaxial test. it includes the influence of end contact and end restraint, the volume variety during the triaxial specimen being saturated, the characteristic of distributing of the gram at the surface of specimen, etc. conclusions are made and some suggestions are presented

    論文的第二部分是數字圖像測量技術在土工三軸試驗中的應用研究，主要內容包括以下幾個部分： （ 1 ）三軸試驗若干問題的討論：利用數字圖像測量技術，主要對三軸試樣的端部約束、端部接觸和端部區域「藏水區」效應、三軸試樣飽和過程中的體積變化以及試樣表面顆粒分佈特性等問題進行討論，給出了一些有意義的結論和建議。
  5. A new way to draw isometric projection drawing is suggested. this method has special and novel character, and has the special significance for to draw advertisement drawing and to draw isometric projection drawing

    提出一種全新的正等軸測投影畫法，該法獨特新穎，畫圖簡單，對廣告宣傳繪畫、計算機畫正等軸測投影圖有較大的實用意義。
  6. For eliminating these shortages, a digital imaging processing technique is developed to measure the deformation of triaxial specimen. the concrete work includes hardware preparation, software development and modification of some attachments of general triaxial apparatus

    在此基礎上，開發研製了適用於土工三軸試驗的數字圖像測量系統，具體工作包括三軸壓力室的改制、硬體配備和軟體開發等。
  7. And the interactive influence of the coaxial diffraction wave components during reconstruction can be eliminated completely by phase - shifting method. this in - line phase - shifting digital holography has been applied to three dimensional microscopy, non - contact measurement, pattern recognition and surface contouring

    這種同軸相移數字全息技術，可以廣泛應用於小尺度三維形貌的快速測量、數字無損干涉計量、圖像識別、顯微成像等領域。
  8. Graphical symbols for piping systems - axonometric representation of graphical symbols for piping, piping accessories and valves etc

    管路系統的圖形符號管路管件和閥門等圖形符號的軸測圖畫法
  9. The error has an effect on image registration and synthesizing. for synthesizing high resolution image, the angles between channels need be measured, then calibration of eut in orbit will be carried out

    這些誤差必然會影響圖像配準、合成等。為了合成高解析度的圖像，需要測出各通道軸向夾角，對其在軌校準，從而減小觀測上的誤差。
  10. In order to gain a high accuracy, all types of error sources in digital image processing system and their influences are discussed in detail. further more, a special auxiliary light, software means and the correction of the system errors are used to improve the accuracy of digital image processing system

    此外，還詳細分析了數字圖像測量系統誤差產生的根源，並且從輔助照明、軟體演算法和系統誤差修正等多方面入手進一步提高數字圖像測量系統的測試精度，經過比較論證，提出了一套針對三軸試驗變形測量的合理高效的定標和誤差修正方案。
分享友人
分享到 Line

分享到臉書