精軋機調整 的英文怎麼說
中文拼音 [jīngyàjīdiàozhěng]
精軋機調整
英文
finishing mill setup- 精 : Ⅰ形容詞1 （經過提煉或挑選的） refined; picked; choice 2 （完美;最好） perfect; excellent 3 （細）...
- 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
- 機 : machineengine
- 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
- 整 : Ⅰ形容詞1 （全部在內; 完整） whole; all; complete 2 （整齊） neat; tidy; orderly Ⅱ動詞1 （整理; 整...
- 調整 : adjust; tune up; trim; trimming; variation; modulation; arrangement; debug; rectification; redres...
-
And it investigates the appearance condition ( including joint, crack, eroding, corrosion, braking pole device rupture, crane - girder ' s gnawing railway and so on ) of the whole crane - girder system on the spot, at the same time, it also actually examines the stress of the beam, chemical ingredient, distortion and railway excursion, etc. through sampling, and based on the actually examined results, it checks and calculates the carrying capacity of crane - girder system. then, based on the investigating on the spot and the calculated result, it discusses the mechanism of fatigue failure of the upper part of welded steel crane - girder, analyses the reason of steel crane - girder in the high - frequency emerging the fatigue crack, institutes the strengthened method of damaged steel crane - girder of accurate packing up workshop of the primary mill plant. finally, it presents some advice and suggestions for the repairing and strengthening method of fatigue crack of upper part of steel crane - girder in the high - frequency
針對包鋼初軋廠精整車間鋼吊車樑上部區域出現裂縫這一問題，本文首先綜述了國內外關于焊接鋼吊車樑上部區域疲勞裂縫的研究現狀；其次對整個吊車梁系統的外觀情況（包括連接、裂縫、腐蝕、銹蝕、制動桿件斷裂、吊車啃軌等）進行了現場調查，抽樣實測了梁的應力、化學成分、變形及軌道偏移等，根據實測結果，對吊車梁系統的承載能力進行了驗算；然後，根據現場調查及計算結果，探討了焊接鋼吊車樑上部區域疲勞破壞的機理，分析了重級工作制鋼吊車梁出現疲勞裂縫的原因，制定了初軋廠精整車間破損鋼吊車梁的加固方案；最後就重級工作制鋼吊車樑上部區域出現疲勞裂縫的修復與加固方案提出了一些意見和建議。And its nnc and nni are both established with the optimal neural network. so the hydraulic bend roller system ' s dynamic response velocity and static tracking precision are advanced. hydraulic bend roller force can operate better and mill ' s dynamic characteristic is improved
將優化網路用於液壓彎輥系統的控制中，採用內模控制方案，辨識器和控制器用優化網路來離線設計、在線調整，提高了液壓彎輥系統的動態響應速度和穩態跟蹤精度，充分發揮了液壓彎輥力對板形的調整作用，改善了軋機系統的動態特性。
分享友人