純剪切試驗 的英文怎麼說

中文拼音 [chúnjiǎnqiēshìyàn]
純剪切試驗 英文
direct shear test
  • 純 : 形容詞1 （純凈; 不含雜質） pure; unmixed 2 （純粹; 單純） simple; pure and simple 3 （純熟） skil...
  • 剪 : Ⅰ名詞1 （剪刀） scissors; shears; clippers2 （姓氏） a surname Ⅱ動詞1 （用剪刀等使細的或薄片的東...
  • 切 : 切Ⅰ動詞1 （合; 符合） correspond to; be close to 2 （用在反切后頭 表示前兩個字是注音用的反切）見 ...
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 試驗 : trial; experiment; test
  1. The results of test and theoretical calculation indicate that the friction device does not slide under minute earthquake, thus the control effort of f - ved corresponds with ved, and the action of frd is the same as pure brace. when disastrous earthquake occurs, the viscoelastic material reaches its shear limits and the friction device begins to slide, so the control effort of f - ved is the best

    試驗結果和理論計算結果表明，在多遇地震下摩擦機構不起滑，粘彈性-摩擦阻尼器的減振效果和純粘彈性阻尼器相當，而摩擦阻尼器的作用相當于純支撐；在罕遇地震下粘彈性材料達到剪切極限，摩擦機構起滑，故粘彈性-摩擦阻尼器的減振效果最好。
  2. The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film

    試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。
  3. Anisotropic parameters can be determined using six simple experiments, tensile tests ( or compression tests ) and pure shear tests

    摘要對於三維屈服函數，正交異性材料異性參數的確定需要單拉（或單壓） 、純剪切等六個簡單試驗。
  4. Based on a yield function put forward by zhou weixian, pure shear yield curves can be obtained indirectly using six simple compression experiments, when pure shear experiments can ' t be finished

    基於周維賢提出的屈服函數，針對無法進行純剪切試驗的情況，可以採用六個簡單壓縮試驗間接地確定純剪切屈服曲線。
分享友人
分享到 Line

分享到臉書