純態硬度 的英文怎麼說

中文拼音 [chúntàiyìngdù]
純態硬度 英文
passive hardness
  • 純 : 形容詞1 （純凈; 不含雜質） pure; unmixed 2 （純粹; 單純） simple; pure and simple 3 （純熟） skil...
  • 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
  • 硬 : 形容詞1 （堅硬） hard; stiff; tough 2 （剛強; 堅定; 強硬） strong; firm; tough; obstinate 3 （勉...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 硬度 : hardness; solidity; scirrhosity （腫瘤的）
  1. The degrees of crystallinity of pure ptfe under the different conditions of water cooling, air cooling and furnace - varying cooling were made comparison by xrd. the thermal stability of pure ptfe and solid lubricant was analyzed by dsc - tg ; the composition and valence state of elements in the surface of carbon fiber, solid lubricant before and after friction test and lubricant transfer film were characterized by xps ; the frictional property of solid lubricant was tested by pin and disk test rig. the frictional wear property of solid lubricant between embedded bearing sleeve and steel axle friction pair ring was tested by special simulate test machine, the hardness of solid lubricant was tested by pm ; the compression strength of solid lubricant was tested by material test machine

    用sem表徵原料微觀結構、摩擦表面及潤滑轉移膜表面形貌：用xrd進行原料物相分析，及比較水冷卻、空氣冷卻、隨爐冷卻三種工藝條件下的純聚四氟乙烯樹脂的結晶度；用dsc - tg分析純聚四氟乙烯樹脂及固體潤滑劑的熱穩定性；用xps表徵碳纖維表面、固體潤滑劑摩擦前後表面、潤滑轉移膜表面的元素組成、價態變化；用銷盤式摩擦磨損試驗機對固體潤滑劑進行摩擦性能測試；採用專用的臺架模擬試驗機對固體潤滑劑鑲嵌軸承套與鋼軸摩擦副間的摩擦磨損性能進行測定；用萊次偏光顯微鏡（ pm ）測試固體潤滑劑的硬度；用材料試驗機測試固體潤滑劑的抗壓強度等。
  2. 5. after high temperature annealing the hardness of the composites did not reduced obviously until 973k, this temperature greatly exceeds that of pure copper ( after cold machining, the temperature is 423k )

    本文制備的材料經高溫退火后的硬度明顯降低溫度點為973k ，大大超過了純銅（冷加工態）的423k ，而且熱穩定性能較好。
  3. Sintering or friction all brought about chemical change in the surface of solid lubricant and the change of valen ce state of mo, s, fe and so on ; the micro - hardness of pure ptfe was minimum and the surface - hardness of solid lubricant was increased with the increase of additional packing filler in formula ; the compressive strength of pure ptfe was minimum and its compressive strength could be increased notably by adding organic and inorganic filler. but not more additional amount, more notable increase of compre

    、 feso4 、 cus等物質;燒結及摩擦均使固體潤滑劑表面發生化學變化，使mo 、 s 、 fe等元素的價態發生變化;純ptfe的顯微硬度最低，固體潤滑劑的表面硬度基本是隨著填料加入量的增加而增加的;純ptfe的抗壓強度最低，在ptfe樹脂中加入無機填料均可明顯提高其抗壓強度，但並不是加入量越多，抗壓強度提高越明顯。
分享友人
分享到 Line

分享到臉書