線焊接 的英文怎麼說
中文拼音 [xiànhànjiē]
線焊接
英文
line welding-
5 welding by patchcord between the high unit and the low unit, and the unit body can circumgyrate 180, convenient for the cable welding
5高低端單元之間用跳線焊接,單元體可旋轉180 ,方便電纜焊接Uses : cold welding of nonferrous metals such as cu al ag ni pt sn zn ta and some of their alloys
產品用途:對銅、鋁、金、銀、鉑、錫。鉭鈮等有色金屬線材及他們部分合金線材的焊接。Cell connectors and terminal post burning must be done in such a manner that there is complete fusion of the post strap top and the cover lead bushing with the connector ring or terminal post.
連接條和接線柱的焊接必須使極柱頂部和蓋子的鉛襯套與連接條環口或接線柱完全熔焊牢固。A resistance meander wire usually of constantan is welded onto a strip of foil
在金屬薄片上焊接了改良的電阻導線,通常使用的是康銅導線。Radiographic examination of fusion welded joints in metallic materials
金屬熔化焊焊接接頭射線照相Long rails in jointless track are usually made on welded rail site or in railway welded rail factory
摘要無縫線路長鋼軌道常由鐵路焊軌廠或現場焊軌基地焊接。Microstructure and toughness of welding coarse - grain heat affected zone in ti - v - nb microalloy pipeline steel
微合金管線鋼焊接粗晶區組織及韌性Idea of differential plane is introduced in the calculation of orientation of normal line, and optimal orientation for electron gun is obtained. this work is helpful for guaranteeing welding quality
在法線姿態的計算中,引入微分平面的設計思想,獲得了焊接過程中的最佳姿態,保證了焊縫質量。The steel construction is made up of roof beam, post, purlin, roofing and wall, adopt the automatic production line to weld and take shape in the factory, construction site spend high - strength bolted joint reduce weld work load, make progress and quality receive the complete assurance
鋼結構由梁、柱、檁條、屋面和墻體組成,工廠內採用自動化生產線焊接成形,施工現場用高強螺栓連接,減少了焊接工作量,使進度和質量得到完全保證。The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased
本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化,結果表明:採用普通工藝焊接時,葉片焊后殘余拉應力出現在焊縫及其附近區域,並且在葉片出水邊的熔合線附近(危險區域)出現了峰值;在採用優化的分段焊時,先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值,降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比,與冷卻面積成反比,並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。Standard reference radiographs for examination of aluminum fusion welds
用於檢驗焊接中鋁的標準參考射線照片Care must be exercised in attaching the lead wires to the soldering tabs.
在往焊接接線片上焊導線時必須非常小心。Usually, glass insulated terminals are either soldered or cemented into the throughhole in the case.
通常是把玻璃絕緣接線端焊接或者是粘合在殼體上的通孔內。Figure 7 : tail or crescent bond is the shape of the thermosonic bond on the substrate ( ball bond is on dimensions are shown in the box to the right of the figure
月牙形焊接(熱超聲焊的末端)的尺寸和形狀直接與引線直徑和毛細管的幾何形狀有關。Figure 6 : drawing3 showing wedge bonding operation on the second bond, at the substrate bondinger. figure 7 : tail or crescent bond is the shape of the thermosonic bond on the substrate ( ball bond is onthe die side )
月牙形焊接(熱超聲焊的末端)的尺寸和形狀直接與引線直徑和毛細管的幾何形狀有關。Code of the welding technique for aluminium bus
鋁母線焊接技術規程Acceptance tests for nd : yag laser beam welding machines - machines with optical fibre delivery - part 2 : moving mechanism
Nd : yag激光射線焊接機器的驗收試驗.帶光纖傳送的機器.第2部分:移動裝置Welding - recommendation for welding of metallic materials - part 6 : laser beam welding ; german version en 1011 - 6 : 2005
焊接.金屬材料焊接的推薦標準.第6部分:激光射線焊接Beam lead bonder
梁式引線焊接機Code for construction and acceptance of welding aluminium - bus - bar
鋁母線焊接施工及驗收規程分享友人