緻密度 的英文怎麼說

中文拼音 [zhìmìdù]
緻密度 英文
consistency
  • 密 : Ⅰ名詞1 （秘密） secret 2 [紡織] （密度） density 3 （姓氏） a surname Ⅱ形容詞1 （距離近; 空隙小）...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. We also attainted mosi2 / sic composite by using melting mosi2 infiltrated sic body which shaped by sic powder. the result show that the diameters of sic particle and shaping methods have effect on the composite ' s microstructure and properties

    另外，嘗試了用mosi _ 2在2050下浸滲直接由sic粉體成型的坯體制備mosi _ 2 / sic復合材料。採用sic顆粒的級配有利於提高坯體密度，但是降低燒結體的緻密度。
  2. Mas precursor powders were uniaxially pressed at 100 mpa employing a lubricated steel cylindrical mold. after sintering at 1450 for 2 hours, single - phase cordierite ceramic is prepared, and its relative density is 95. 1 %

    Mas先驅體粉末在100mpa的軸向壓力下成型后，經1450無壓燒結2小時，得到單相堇青石陶瓷，其緻密度達95 . 1 。
  3. The results show that " the frame - pack rolling " technology can increase the densify, avoid cracking during rolling, and effectively improve the deformability and mechanical properties of the spray deposited porous aluminum alloy sheets

    結果表明：外框限制軋制工藝提高了噴射沉積多孔材料的緻密度，避免了軋制過程中裂紋的形成，有效地改善了噴射沉積板坯的軋制性能及材料的力學性能。
  4. Cyclic pressing is a new kind of densification processing, which is introduced to densify as - deposited ring of al - 20 % si / sicp. this paper includes the densification result and rule of this technics. the research shows that this technics can be successfully used to densify spray - forming porous material and can be availably adopted to improve mechanical performance and microstructure. this technics is characterized by simple equipment 、 small expense and flexible process, and these characters will make it come true to producing spray - deposited rings less costly

    本文採用一種新型緻密化工藝?楔壓工藝?對噴射沉積al - 20 % si / sicp大環進行了緻密化加工，採用密度硬度分佈、抗拉強度變化和檢測顯微組織變化的實驗研究方法對其緻密化效果及該工藝規律進行了研究，通過研究表明了楔壓工藝可以成功地用來緻密化噴射沉積多孔材料，該工藝有效地提高了噴射沉積大環件的緻密度和抗拉強度並改善了組織。
  5. But it also includes two fatal disadvantages : first, at is difficult to be sintered and its density is low, which causes its lower strength ; second, in the temperature range of 1023 - 15 73 k, at can decompose into al2o3 and tio2 easily, which can cause the stress concentrated and raise the heat expansion rate

    但是該材料本身存在的兩大致命的缺點，在很大程度上限制了它的廣泛應用： （ 1 ） 、鈦酸鋁難以燒結，燒結體的緻密度低，因而強度不高； （ 2 ） 、在750 1300的溫度范圍內易分解成氧化鋁和二氧化鈦，造成材料內部應力集中，並使材料的熱膨脹率升高。
  6. In this paper, nanosized al2o3 ceramic particles were chose as reinforcing phase. enhanced with ultrasonic wave the particles were covered with copper using method by electroless plating, the copper - matrix composite was developed by hot - press sintering process of the composite powder. the composition, microstructure, hardness, density and dry sliding wear property of the new material have been studied

    研究路線為：選用納米級al _ 2o _ 3陶瓷顆粒作為增強相，在超聲波的環境中用化學鍍的方法完成對納米al _ 2o _ 3陶瓷顆粒表面的金屬銅包覆，採用熱壓燒結成型技術以復合粉末為原料制備成納米al _ 2o _ 3陶瓷顆粒增強銅基復合材料，研究分析復合材料的成分、組織結構、硬度以及緻密度，對試樣進行了干滑動摩擦磨損實驗。
  7. The research on the properties of the copper nanoparticles / paraffin thermosensitive composite materials reveals : the thermal sensitivity and the thermal expansion are " aried by the cempress moulding in heat condition with the change in density ; the thermal sensitivity is varied by the mechanical milling with the change in particle shape and particle dimension ; the mass ration of copper and paraffin in the composite materials also affects the thermal sensitivity, the thermal expansion and the thermal stability with the change in copper nanoparticles and paraffin interface

    對復合顆粒進行壓力成型后制備的復合材料進行性能測試分析表明：熱壓成型工藝通過改變復合材料的緻密度來影響材料的熱敏性和熱膨脹性。高能球磨工藝主要通過改變球磨時間使銅粒形狀和粒徑發生變化來影響復合材料的熱敏性，以及改變銅粉和石蠟的質量比使納米銅粒和石蠟的復合界面發生變化來影響材料的熱敏性、熱膨脹性和熱穩定性。
  8. The research history of fullerene and cnts was short, but their characteristics have great value in practical application. metallic nano - particles have different crystal orientation with different synthetical techniques. their special mechanical, optical and electrical properties will drive the development of magnetic materials, electronic materials and optical materials et. al

    納米金屬粒子在不同的制備工藝下具有不同的結晶形態，而且其具有的特殊的力、熱、光、電、磁的性質，引起了在磁性材料、電子材料、光學材料、高緻密度材料等方面的應用。
  9. Otherwise, sic can strengthen the samples by its pinpoint effect. the results also showed that the hardness of samples rise with the increase of sic, but the densities decline

    Sic的加入，增大了（ zro2 ） al2o3復合材料的硬度，但降低了材料的燒結活性，使燒結體的緻密度下降，材料的強度和韌性也有所下降。
  10. The iron covered silicon powder was fabricated separately by the milling method and the mixing method. treated separately at 500, 600, 700, 800, 900 and 1000 for 1 minute, the iron silicon alloy bulk was attained. it also found that the density of the bulk was enhanced by the boost of the treated temperature

    實驗分別採用球磨法和混料法制備鐵硅包覆粉末，採用放電等離子燒結技術分別在500 ， 600 ， 700 ， 800 ， 900 ， 1000保溫一分鐘進行處理，得到鐵硅合金塊體，研究發現，隨著處理溫度的提高，塊體的緻密度隨之增加，顯微結構的分析表明，塊體基本保持了包覆粉末原始自然狀態。
  11. The influence of nano - al2o3 on the sintering and the properties of the si3n4 ceramics was researched in this paper. the samples with different amount of nano - al2o3 were obtained by using pressureless sintering at 1600, 1650, 1700 in the nitrogen atmosphere. the microstructure and the composition of the ceramics were determined by the means of x - ray, sem, micro - hardness meter etc. it is show that the sisty ceramics can be densified at 1650c to % percent of the theory density through the addition of nano - al2o3 ( the value could be 90 percent by other technique ). the crystalline growth of the cylindrical - si3n4 and the ratio of its longitude to its diameter are increased with the addition of nano - al2o3. a uniform microstructure and an fined crystal as well as more sialon phases can be obtained in the si3n4 ceramics through the addition of that

    實驗結果表明：在碳管爐中、氮氣保護下進行燒結，添加劑為納米al _ 2o _ 3粉末時，由於納米粉末的高活性、高燒結驅動力，在1650就可使si _ 3n _ 4完全地燒結，並使其緻密度可達理論密度的96以上（比其它工藝高6左右） ；同時，納米al _ 2o _ 3地加入大大促進了長柱狀? si _ 3n _ 4的生長和發育及柱狀晶長徑比的提高，使微觀結構均勻、細化，形成了更多力學性能優異的固體? sialon相，減少了不利於陶瓷材料性能的晶間玻璃相，凈化了晶界。
  12. The magnetic properties result of the sample state that the ultimate 800 - treated mixed sample has the coercive of 4. 01oe and the core loss at w10 / 50 of 3. 28w / kg. the main reason may be there was large of oxide in the sample and the density was not high

    樣品的磁性能的結果表明， 800混料樣品最終的矯頑力為4 . 01oe ，鐵損w10 50為3 . 28w kg 。所得到的最終樣品的磁性能較差，主要是因為樣品中存在較多的氧化物和樣品的緻密度不夠理想。
  13. To insure more densification but deformation of glass beads, the green density should be increased, and the burnout temperature of binder should be below the toplimit of transformation temperature

    為保證絕緣子獲得較高緻密度而不變形，應盡量提高生坯密度，溫度同時排蠟應低於該種玻璃的轉變溫度上限。
  14. Abstract : by mean of adjusting the position and shaps of risers, shrinkages and porositi es in balancing axle case are eliminated on the principle of direirional solidification, its density is a lso improved

    文摘:根據動態順序凝固的原則，對斯太爾平衡軸殼鑄鋼件設計合理的冒口位置和形狀；有效地消除了鑄件熱節部位的縮孔，提高鑄件的緻密度。
  15. When the content of mgtiao5 is 10mol % and the composite is kept at the 1100 for loh, the decomposition rate of at is far below 9 % ; the density of sintered material at 1500 with additive m2t is about 10 percent higher than that of those without any additives

    當鈦酸鎂的含量為5mol時，鈦酸鋁在1100保溫10小時，其分解量要小於9 ；而且在1500燒結得到的燒結體緻密度比沒有引入添加劑高近10個百分點。
  16. The analysis of microstructure of samples showed that the grain of tio2 were very small under 700, the distance of grain became small with temperature increasing, the rate and size of pore was decreasing. the relative density of sample at 900 was 97 % and the grain size of sintered body was about 200nm. when the temperature exceeded 1100, the grain size of body grew up several times ( > 2 m )

    Tio _ 2燒結體sem顯微形貌分析表明：低溫（ 700 ）時坯體內顆粒無明顯長大，燒結體緻密度不高（ 80 ）晶粒間距隨溫度升高而變小，氣孔率也隨之降低，氣孔尺寸變小；當溫度超過900時，晶粒間連接緊密，燒結體內出現大量絮狀物質，緻密度大幅度提高，達97以上，小氣孔已聚集成大孔洞且分佈均勻，晶粒長大不明顯（ 200nm左右） ；當溫度超過1100時，燒結體緻密度有所提高，但晶粒尺寸出現異常長大，長大了十幾倍（達2 m以上） 。
  17. Any products were prepared without impurities. the sps method was used to sintering the zrnisn - based compounds. the influence of different reaction temperature and holding time to density was discussed in detail

    採用放電等離子法（ sps ）燒結制備zrnisn基化合物，並探討了不同的燒結溫度和燒結時間對材料緻密度的影響。
  18. The results indicate that arc melting is a good method to produce nb - si system intermetallics due to its simpler technics, lower cost and compact products. however, powder metallurgy is found to be not suitable to produce the nb - si system intermetallics due to its coarse and loose products resulting from the poor molding property of nb and si mixed powders. optical floating zone technology, which is used to fabricate nb - si intermetallic composites for the first time, is also found to be a good way to produce nb - si system intermetallics because of its compact products and good property despite of its relatively high cost

    結果表明，電弧熔煉方法制備得到的nb - si系金屬間化合物比較緻密，且制備工藝簡單，經濟實用，是一種合適的nb - si系金屬間化合物制備方法；由於nb 、 si元素粉末的成型性很差，用粉末冶金方法（熱壓燒結和冷等靜壓）制備的nb - si系金屬間化合物表面粗糙、緻密度低，且成本較高，不宜用於制備nb - si系金屬間化合物；首次用光學懸浮單晶生長技術制備的nb - si系金屬間化合物復合材料緻密度很高，盡管成本稍高，但由於性能最佳，也是一種合適的nb - si系金屬間化合物制備方法。
  19. Extrahaustorial membrane wrinkled, stained more deeply, wrinkled, and perforated

    吸器外質膜皺褶，電子緻密度加深，並出現孔洞。
  20. The composite was pressed and sintered again to further enhance its synthetical properties. through this treatment, interface binding strength, compactness, conductivity and mechanical properties of the composite were prominently increased

    復壓復燒處理后，銅基體與碳纖維之間結合狀態良好，復合材料的緻密度、電導率及機械性能均有顯著提高。
分享友人
分享到 Line

分享到臉書