聯接螺栓 的英文怎麼說

中文拼音 [liánjiēluóshuān]
聯接螺栓 英文
attachment bolt
  • 聯 : Ⅰ動詞（聯結; 聯合） unite; join Ⅱ名詞（對聯） antithetical couplet
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 螺 : 1. [動物學] （軟體動物） spiral shell; snail; conch 2. （螺旋形的指紋） whorl （in fingerprint）
  • 栓 : 名詞1. （可開關的機件） bolt; plug 2. （塞子） stopper; cork
  • 聯接 : [電工] strapping; coherence; lashing; link up; coupling; [宇航] mate聯接板 gusset piece; gusset p...
  • 螺栓 : bolt; screw bolt; threaded bolt
  1. Using the optimum calculating method, some important technical parameters could be determined, that is, optimum supporting force, allowable deformation of rock mass, cross section area of u - shape set, pre - tight force and diameter of the bolt as well as torque to provide optimum supporting force

    用這一計算方法能求出巖石恆阻支護的重要技術參數，即最優（小）恆阻支護力、圍巖最大允許變形量、恆阻u型鋼支架的截面積、聯接螺栓的預緊力和直徑及最優支護力的擰緊力矩。
  2. According to the analysis of the table lookup, the graph method and the simulating formula method of selecting bolt diameter without controlling pretightening force under dead load were presented in this paper

    摘要通過對查表法資料進行分析，提出了靜載時選擇不控制預緊力的緊螺栓聯接螺栓直徑的圖線法和模擬公式法。
  3. Abstract : based on the fuzzy mathematics, it establishes the rules of the fuzzy reliability design for the bolt - joint set, discusses the effect of pre - tighten force and the axial changing load on the set, and shows an example

    文摘:將模糊數學理論引入可靠性設計中，考慮預緊力和軸向變載荷狀態的影響因素，建立螺栓聯接的模糊可靠性設計準則，並給出了設計實例。
  4. B connections for general use and fluid power - ports and stud ends with iso 261 threads with elastomeric or metal - to - metal sealing - stud ends with metal - to - metal sealing type b

    普通和液壓用聯接結件.用iso 261螺紋的彈性或金屬與金屬間密封的氣門和雙頭螺栓端頭
  5. The key position bolt of the engine include connecting rod, crankshaft, main bearing, cylinder head, flywheel and shock absorber bolt, all of which belong to bolt fastening

    發動機關鍵工位螺栓包括連桿螺栓、曲軸螺栓、主軸承蓋螺栓、氣缸蓋螺栓、飛輪螺栓和減振器螺栓等均屬螺紋聯接。
  6. Attach each leg to the bottom of the enclosure using the three nuts, bolts, and washers provided for each leg. tighten bolts securely

    將每個支柱聯結到外殼底部，對于每個支柱，採用三套螺母、螺栓和墊圈與外殼進行連接。小心緊固螺栓。
  7. Further more, the fracture possibility is analyzed with fracture mechanics after the stress calculation of local high stress area around the bolt hole in shell flange and the measurement of fracture toughness of gray cast iron. the improving structure of bolts connected head and shell flange is brought forward

    此外，在計算獲得缸體法蘭螺栓孔局部高應力區的應力水平后，由斷裂力學分析發生脆性斷裂的可能性，並提出烘缸缸體與缸蓋聯接結構的改進方案。
  8. Application of conical hydraulic connecting bolt to coupling of turbo - generator set

    錐形套液力連接螺栓在汽輪發電機組聯軸器上的應用
  9. The valve can be installed in horizontal or vertical. add seal cushion between two flanges connection and screw down bolt

    本閥可水平或垂直安裝，安裝時兩法蘭聯接中間必須加密封墊片，然後均勻鎖緊螺栓。
  10. Abstract : according to the deformation or fracture caused by uneven loads on the structural connection, the smart structure with sensible and regulative functions has been proposed to be used in bolt groups. the smart structure is constituted with the auto - even - load connecting component made of the shape memory alloy material. the mechanical behavior of the auto - even - load component in the bolt groups is analyszed. its auto - even - load and the regulative principle to prevent the fracture are also studied

    文摘:本文針對結構聯接受力不均易產生變形或破裂等問題，提出了在螺栓組中加裝由形狀記憶合金材料製作的自動均載傳力件構成具有感知和調節功能的智能結構，並對螺栓組聯接加裝均載傳力件后的均載防斷功能進行了力學特性分析，特別是對螺栓組傳力件自動均載和防斷的調節原理進行了研究，最後進行了實驗驗證。
  11. A new method of pre - tightening for king diameter coupling bolt

    大直徑聯接螺栓預緊的一種新方法
  12. Installation of flange connecting valve is on diagram. lock down the connecting bolt after add sealing washer

    安裝如示意圖，加密封墊后均勻鎖緊聯接螺栓。
  13. The transmission part cannot be hoisted and damaged. add sealed shim between the two flanges and then lock down the bolt equably

    安裝時傳動部分不允許作吊裝用，並嚴禁損傷。兩法蘭連接中間需加密封墊片，然後均勻擰緊聯接螺栓。
  14. Pay attention to the flow direction of medium showed on the body. installatio of flange connecting valve is on diagram. lock down the connecting bolt after add sealing washer

    安裝時請注意閥體上標注（箭頭）的介質流向，安裝如示意圖，加密封墊后均勻鎖緊聯接螺栓。
  15. Pay attention to the flow direction of medium showed on the body. installation of flange connecting valve is on diagram. lock down the connecting bolt after add sealing washer

    安裝時請注意閥體上標注（箭頭）的介質流向，安裝如示意圖，加密封墊后均勻鎖緊聯接螺栓。
  16. In this paper the author describes a way of determining the residual pre - tightening force after adding elastic elements to the connecting bolt at the flange on ball mill ' s shell and therefore a formula is induced

    闡迷了球磨機筒體法蘭聯接螺栓增加彈性元件后其剩餘預緊力的確定方法，並導出了相應的計算公式。
  17. In order to solve it radically, making power assembly of bj1036e2f1 light truck the research object and through dynamic simulation analysis of power assembly, this thesis obtains the distribution rules of forces of the bolts linking three shells mentioned above and the relation between forces of the bolts and rotate speed of engine. after finite element mode analysis of these three shells, inherent frequency and vibration model of shell of power assembly are gained, and thus its dynamic character is realized. based on computer simulation analysis, experimental model of power assembly is acquired by vibration test and strength test of shell of power assembly, and the relation of forces of the shell and rotate speed of engine and imbalanced mass of rotate components is studied

    為了從根本上解決該問題，本論文以bj1036e2f1輕卡動力總成為研究對象，通過動力總成的動力學模擬分析，找出了三殼之間聯接螺栓受力的分佈規律和螺栓受力與發動機轉速的關系；通過三殼的有限元模態分析，得到了動力總成殼體的固有頻率與振型，從而了解了動力總成殼體的動態特性；在計算機模擬分析的基礎上，通過動力總成殼體的振動測試和強度測試，得出了動力總成的試驗模態，並研究了殼體受力與發動機轉速和旋轉部件不平衡質量的關系。
  18. The paper expounds how to find out the potential safe problems and unobvious defects, such as beyond - limit deflection in fixed girders for gantry bucket wheel stacker / reclaimer, by means of completely checking fixed girders, movable beams, geometric shapes of stiff and flexible supporters, metal thickness and welding and how to solve the safe problems and remove the defects

    摘要通過對門式斗輪堆取料機固定梁、活動梁、剛性支腿、撓性支腿的幾何形狀、金屬厚度、焊縫狀況、聯接螺栓狀況進行全面檢測，發現門式斗輪堆取料機固定梁存在下撓超標的安全隱患和其他非明顯缺陷，從而對堆取料機的安全狀況有了全面的掌握，並根據檢測結論對固定梁下撓缺陷及時進行校正消缺，避免發生設備垮塌事故，保證了堆取料機的安全穩定運行。
  19. Agricultural tractors and machinery - trailer coupling - bolt coupling for coupling - ring 40

    農業用拖拉機和機械.拖車聯軸節. 40聯接環用螺栓聯軸
  20. Mechanical connections between towing vehicles and trailers ; automatic bolt coupling 50 ; dimensions and calculating data

    牽引車和掛車的機械連接.第1部分: 50 mm自動螺栓聯軸
分享友人
分享到 Line

分享到臉書