肋片管 的英文怎麼說

中文拼音 [lèipiānguǎn]
肋片管 英文
extended surface tube
  • 肋 : 肋構詞成分。
  • 片 : 片構詞成分。
  • 管 : Ⅰ名詞1 （管子） pipe; tube 2 （吹奏的樂器） wind musical instrument 3 （形狀似管的電器件） valve;...
  1. Tube and fin radiator

    肋片管式散熱器
  2. Then, a thorough discussion and sum ? p about the main construction process of cfst tied ? rch bridge without wind bracing is presented in the paper in association with the construction practice of the bridge. in addition, the author put emphasis on the static calculation of two point integral hoisting construction method in single cfst arch rib. futhermore, the stabilization of arch rib in construction and service stage are analyzed detailedly

    本文結合該大橋的施工實踐，對無風撐鋼管混凝土系桿拱橋的主要工藝施工流程進行了全面論述和總結，並重點對單片鋼管拱肋兩點整體吊裝的結構受力進行了靜力計算及對拱肋在施工和運營階段的穩定進行了分析。
  3. The compact algorithms for heat release from floor, indoor thermal environment, control characteristic and energy efficiency of room with imbed pipe floor heating system were studied in this dissertation. the heat release from floor is key nodes in designing of imbed pipe floor heating systems. the existing plate fine model is corrected to improving its accuracy by amending the temperature of fine root

    文中對原有的平面肋片簡化演算法採用了肋基溫度修正，提高了其計算準確度；根據埋管低溫熱水輻射地板結構特點，利用地板導熱形狀因子計算地板當量熱阻，首次提出了更為簡便的當量熱阻演算法，該演算法將影響地板傳熱的物性參數和各種結構參數歸結到當量熱阻中，方便於工程分析和計算。
  4. Based on this model, wall temperature of spiral finned tubes has been computed to verify the validity of the model put forward in the paper

    建立了螺旋肋片管低溫再熱器的壁溫計算數學物理模型，並對螺旋肋片管低溫再熱器進行了壁溫計算。
  5. The experimental correlations for the forced convection - condensation heat transfer of flue gas in the heat exchanger are obtained by the experimental study result

    根據實驗研究結果擬合出了肋片管式冷凝換熱器煙氣強迫對流凝結換熱的實驗關聯式。
  6. Design of the spiral finned tube low temperature reheater has been made by means of applicable investigation of spiral finned tubes, some mathematical - physical models for computing spiral finned tubes wall temperature have been set up

    通過對螺旋肋片管的應用探討，進行了螺旋肋片管低溫再熱器的設計。
  7. The application of the first technology can resolve the problem that the fin - root is easy to corrode, effectively reduce the contact heat resistance between the fin - root and the tube, and enhance the heat transfer performance of the heat exchanger

    採用先鍍后脹再鍍加工工藝，不僅解決了肋片管式冷凝換熱器肋基處易腐蝕問題，而且明顯降低了肋基處肋片與肋管的接觸熱阻，增強了換熱器的換熱性能。
  8. Applying amorphous ni - cu - p composite electroless plating as anticorrosion plating, the heat transfer performance of the fin - tube condensing heat exchanger processed by the plating - expanding - plating technology and the expanding - plating technology is experimentally studied

    摘要以非晶態鎳銅磷復合化學鍍層作為防腐鍍層，對採用先鍍后脹再鍍和先脹后鍍2種加工二藝的肋片管式冷凝換熱器進行了換熱性能實驗研究。
  9. After the rationality of theoretical model has been testified, going along a series of numerical simulation and find the best ratio of evaporation segment and condensation segment by means of analyse the temperature variety of the electronic element surface on the effect of the radiator structure change. a series of strenthen step about heat transfer put forward theoretically by means of numerical analysis focuse on the thermal resistant of each tache of the heat transfer

    在證實了本理論模型是合理的基礎上，本文根據所建立的模型進行了一系列的數值模擬計算，分析了熱管型電子器件散熱器的結構尺寸（蒸發段和冷凝段的長度比、肋片的高度等）變化對發熱器件表面溫度的影響，得到了蒸發段和冷凝段的最佳長度比。
分享友人
分享到 Line

分享到臉書