腹切板 的英文怎麼說
中文拼音 [fùqiēbǎn]
腹切板
英文
ventral cutting plates-
In this experiment, radio - immunoassay and hybridization in situ were applied to observe the insulinotropic activities of glp - 1 ( 7 - 36 ) nh2 and reveal the mechanisms underlying this process. methods : rat pancreases were removed from 3 - 5 day - old sprague - dawley rats and dissected into 0. 5mm3 segments and islets were isolated by the collagenase digestion method of wangling et al. thoroughly washed islets and suspended in modified rpmi - 1640 medium supplemented with 10 % fetal bovine serum, and added to 50ml cell culture flasks
方法：胰島的分離參照王玲等的方法，每次實驗取新生3 - 5天sd大鼠，無菌條件下剖腹取出胰腺，剪切為0 . 5mm ~ 3的組織塊， v型膠原酶消化30min后，離心洗滌，懸浮於完全培養基，接種入50ml培養瓶，於5 co _ 2 、 95空氣條件下培養20h ，轉板純化，接種於96孔培養板培養24h ，按實驗要求進行實驗。A scottish dish consisting of a mixture of the minced heart, lungs, and liver of a sheep or calf mixed with suet, onions, oatmeal, and seasonings and boiled in the stomach of the slaughtered animal
哈吉司羊肉一種蘇格蘭菜，由綿羊或牛切碎的心，肺，肝與板油，洋蔥，燕麥片和調味料混合在被屠宰動物的腹中煮熟而成Shear properties in the plane of the panel ( interlaminar shear ) duplicate the kind of shear stress encountered in such glued structural assemblies as structural sandwiches and adjacent to gluelines between flanges and webs in box - beams and i - beams and gusset plates in trusses
面板平面的剪切特性（層間剪切） ，與夾層結構這類粘合組件，以及箱形梁、工字梁凸緣與腹板間的焊接層和桁架加固板附近位置所受的剪切應力類型相同。This specimen of a pigeon, being dissected along the middle line of its belly, whose chest and abdoment walls, chest bone, right leg, right side chest muscle and its artery and vein, as well as the portion of liver being removed, the left side chest muscle being turned outward with all intestines being pulled outside, was fixed on the board
本標本沿鴿腹部中線剖開，切除胸腹壁、胸骨、右後肢等，及部分肝以及右側的胸動、靜脈和胸肌；左側胸肌翻向外側，大小腸從體腔內拉出體外，標本背向襯板固定。( 2 ) with the universal finite element software ansys, reasonable finite models for such slab - column connection were established and a static non - linear analysis was made, and the rule of this structure about the aspects of force deformation and destruction under vertical load and unbalanced bend are summarized. based on this, a simplified calculation method of punching capacity is advanced
研究空腹板柱節點的傳力機理和破壞模式;對在豎向荷載作用下、豎向荷載和不平衡彎矩共同作用下板柱節點內力、變形和破壞過程進行研究，並提出了抗沖切承載力的簡化計算方法。( 4 ) two component anchor bolt and dowel are afforded, a formulas to calculate the punching capacity of this slab - column connection with the effect of punching component is given in the article. comparing with other kinds, the two punching component is effective. ( 5 ) the possible destroy patterns of this slab - column system are discussed in the text, and design principle and step in detail about slab - column connection are
（ 4 ）提出抗沖切錨栓和銷釘兩種新型抗沖切元件，給出配置抗沖切元件時板柱節點的承載力計算公式;通過比較表明，這兩種新型抗沖切元件對薄壁箱體現澆混凝土空腹板來說是有效的。The mostly content is as follows : ( 1 ) such plate was analyzed continuously in the stimulating sandwich plat method, according to the overseas tests ’ phenomena and results, a crack mode is supposed in the test, and a formulas is deduced to calculate the punching capacity of thin - wall core box cast - in - site reinforce concrete hollow slab, the calculation results agree well with the test results
主要研究內容如下: （ 1 ）採用夾層板理論對這種空腹板進行連續化分析，根據國外的試驗現象和結果，假定破壞模式，推導出薄壁箱體現澆混凝土空腹板柱節點在豎向荷載作用下的抗沖切承載力計算公式，公式的計算值與試驗值吻合良好。Theory analysis in this paper pointed out that the flexural - torsional buckling is the usual form of t - section steel. so the slenderness ratio of flexural - torsional buckling should be used when people give out the b / t ratio by the " equal stability " conception. initial stress, defects and tangent modulus are include in the deduce of the paper to get a rational b / t ratio
通過理論分析指出軸心受力剖分t型鋼整體失穩以彎扭屈曲為主，所以在運用「等穩定」方法確定腹板寬厚比限值時應與桿件的扭轉長細比「掛鉤」 ，並以此為出發點考慮殘余應力、初始缺陷，應用切線模量推導出了較為合理的腹板寬厚比限值公式。分享友人