花鍵 的英文怎麼說
中文拼音 [huājiàn]
花鍵
英文
[機械工程] integral key; spline; multiple key花鍵滾齒機 spline hobbing machine; 花鍵滾刀 spline hob; 花鍵銑刀 spline cutter-
This article takes the lagrange equation as the principle, establishes mathematics modeling to the inertia brake vibration when it brakes, then simulates it with matlab. this paper educed the relation equations between, which are the inertia brake ' s friction coefficient of the brake ring and the friction disk, the mean radius, the braking force, rotation inertia of the driving top and the spline shaft, spiral climbing angle of the brake ' s concave - convex helicoid, the mean effort radius of the concave - convex helicoid, elasticity coefficient of the spring, quality of the driving top and the spline shaft, rotations inertia of the brake ' s rotation part besides the driving top and the spline shaft, suppresses sleeve. provides the theory basis for the inertia brake structure optimization
本文以拉格朗日方程為理論基礎，對慣性制動器在制動時的振動進行數學建模，然後用matlab對其進行模擬，得出了慣性制動器在制動時振動角頻率分別與制動環和摩擦片之間的摩擦系數、制動力的平均半徑、主動頂和花鍵軸的轉動慣量、慣性制動器的凹凸螺旋面的螺旋升角、凹凸螺旋面平均作用力的半徑、彈簧的彈性系數、主動頂和花鍵軸的質量、慣性制動器除主動頂和花鍵軸外其他部分的轉動慣量和、頂壓套的質量等慣性制動器各零部件的物理參數之間的關系，為慣性制動器的結構優化提供了理論依據。Gear and spline drawing standards - part 2 : bevel and hypoid gears
齒輪和花鍵制圖標準.第2部分:傘齒輪和準雙曲面齒輪Small and medium module involute spline rolling machine
中小模數漸開線花鍵滾軋機Broaches for involute spline technical specifications
漸開線花鍵拉刀技術條件Straight cylindrical involute splines measuring pin
圓柱直齒漸開線花鍵量棒Straight cylindrical involute splines inspection methods
圓柱直齒漸開線花鍵檢驗方法Five key groove bit multiple keys bit hexagonal bit
五鍵槽花鍵六角鉆頭For the 30. 2mm shaft, there are still larger over measure to load. the strength is increased by optimization. for ? 17. 4mm shaft, the strength is increased by enlarge the inner dimension of the spline ; for 30. 2mm shaft, the strength is increased by adjust the structure at the boundary between the key groove and the ring groove, the highest stress of the shaft is at bottom and terminal of the spline after optimization
其中對17 . 4mm泵軸的優化，通過增大花鍵內徑，提高了花鍵齒底的強度，降低了應力集中點附近的應力；對30 . 2mm電機軸的優化，通過在軸承鍵的環槽端增加倒角，有效降低了該位置的應力集中，使軸的最大應力點從軸承鍵與環槽的交界處轉變到花鍵根部與收尾的交界處，提高了電機軸整體結構強度的合理性。Specification for straight - sided splines and serrations
直邊花鍵與鋸齒形花鍵規范Technical drawings - representation of splines and serrations
技術制圖.花鍵和鋸齒形花鍵的畫法Summary sheet : straight sided serrations - internal and external
觀察記錄表.直邊花鍵.內部和外部Technical drawings. representation of splines and serrations
技術圖紙.花鍵和鋸齒形花鍵的表示方法Serrations for surgical instruments ; profile angles, groove distances
外科器械的細花鍵連接.齒形角槽的間距Straight - sided spline machining allowance and tolerances
矩形花鍵.加工余量及公差Undercuts for splines - design standard
花鍵齒的牙底削平.設計標準Ball spline rzeppa universal joint
滾動花鍵球籠式萬向節By means of analytical methods based on upper bound element technique ( ubet ), non - axisymmetric element, simulates the forming process of non - axisymmetric involute teeth spline has been introduced, formula of speed fields been derived and the deformation regularity of steady extrusion on the forming process successly described
摘要本文運用上限單元技術（ ubet ） ，引入非完全軸對稱單元，模擬了非完全軸對稱零件漸開線齒外花鍵的成形過程，推導出了成形過程中的速度場公式，並成功地描述了擠壓過程中的變形規律。Numerical simulation of cold extrusion molding process of propeller shaft involute spline
傳動軸漸開線花鍵冷擠壓成形過程數值模擬Analysis of influencing factors on extrusion pressure for cold extrusion forming of splined tube
花鍵管冷擠壓成形擠壓力的影響因素分析Study on cold extrusion process of bearing body with inter and outer spline
內外花鍵軸承體冷擠壓工藝研究分享友人