蒸氣流道 的英文怎麼說

中文拼音 [zhēngqìliúdào]
蒸氣流道 英文
steam flow channel
  • 蒸 : Ⅰ動詞1. （蒸發） evaporate2. （利用水蒸氣的熱力使食物熟或熱） steam Ⅱ名詞[中醫] （將藥物隔水蒸熟） steaming
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 道 : Ⅰ名詞（道路） road; way; route; path 2 （水流通過的途徑） channel; course 3 （方向; 方法; 道理） ...
  • 氣流 : 1 [氣象學] air current; airflow; wind current; airstream2 [語言學] breath氣流紡紗 open end spinni...
  1. The equatorial belt of calms, with its rapid evaporation and strong rising air currents, provides an ideal situation for abundant rain.

    在赤道無風帶，迅速的蒸發和強烈的上升氣流，為大量降雨提供了理想的環境。
  2. As to the simulation, three - dimensional n - s equations and two - phase flow model, in which the liquid toluene spray as discrete particles was considered, were employed to describe the turbulent combustion processes in the combustion chamber. the mass and energy transfer between the two phases were calculated by the droplet evaporation model, and the arrehnius model was used to obtain the gas chemical reaction rate. the details of 3d flow field, the distributions of temperature and compounds were obtained by solving the equations

    數值模擬方面，應用三維湍流n - s方程以及顆粒軌道模型描述了激光器燃燒室內部的噴霧兩相燃燒流動過程，兩相之間的質量、能量交換由液滴蒸發模型計算，氣相化學反應速率由arrhnius公式計算，通過耦合求解氣液兩相模型方程，模擬了燃燒室三維流場，得到了燃燒室內的溫度和組分濃度分佈。
  3. Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting ". under the condition of constant diameter of welding wire and its feeding speed, the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply. if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition, the welding process will be stable with less spatter and smooth weld bead

    通過分析不同焊接規范下的焊接電壓和電流的波形.研究了水蒸氣保護下電弧及熔滴過渡的特點，發現其電弧過程行為有「燃弧?熄弧?短路」和「燃弧?短路」兩種形式.在焊絲直徑和送絲速度一定的情況下，通過調節焊接迴路中的電感量和電源電壓，可以改變電弧的過程行為形式.若電弧過程呈「燃弧?熄弧?短路」交替進行，並且熄弧時間最短時，短路過渡頻率最高，在這種情況下，飛濺小，焊道成型好，焊接過程穩定
  4. On - line measurement system for gas flux in the pipeline based on vapour pressure equation

    基於蒸汽壓方程下的管道煤氣流量在線計量系統
分享友人
分享到 Line

分享到臉書