螺栓孔 的英文怎麼說

中文拼音 [luóshuānkǒng]
螺栓孔 英文
bolt hole
  • 螺 : 1. [動物學] （軟體動物） spiral shell; snail; conch 2. （螺旋形的指紋） whorl （in fingerprint）
  • 栓 : 名詞1. （可開關的機件） bolt; plug 2. （塞子） stopper; cork
  • 螺栓 : bolt; screw bolt; threaded bolt
  1. Holes in bolt and screw shanks and slots in nuts for cotter pins

    扁銷用螺栓孔與螺母螺桿尾和槽
  2. Dead weight loading simulating that of the bolts was applied at the bolt holes through the agency of steel balls and buttons.

    螺栓荷載是用死荷重來模擬的，以鋼球和壓鈕作為代用件，通過它們將此荷載施加於螺栓孔。
  3. Drilling holes for screw on the head of high pressure vessels

    高壓容器主螺栓孔加工
  4. There are three lifting holes and one lifting bolt hole on thefront and rear of the machine bed for plugging lifting hooks or bars

    床身前後共有三個起重孔和一個起重螺栓孔，用以插入起重工具。
  5. Further more, the fracture possibility is analyzed with fracture mechanics after the stress calculation of local high stress area around the bolt hole in shell flange and the measurement of fracture toughness of gray cast iron. the improving structure of bolts connected head and shell flange is brought forward

    此外，在計算獲得缸體法蘭螺栓孔局部高應力區的應力水平后，由斷裂力學分析發生脆性斷裂的可能性，並提出烘缸缸體與缸蓋聯接結構的改進方案。
  6. Nb : special end plates and bolting details can be made available upon request

    注：也可根據客戶要求製作特殊形狀的包邊板和螺栓孔。
  7. Lug body available with iso flange dimensions and metric bolt hole threads. for dead - end service use lug style ( rated 200 psi for this service )

    凸耳閥體也可配置iso法蘭尺寸和公制螺栓孔螺紋。用於終端位置可採用凸耳結構（此時額定壓力為200psi ） 。
  8. According to the characteristics of the plexiglas, using the principles of the stress field intensity ( sfi ), a local stress approach for the evaluation of the fatigue life of the plexiglas structures is proposed

    根據有機玻璃特點，利用場強法原理，建立了有機玻璃裂紋形成壽命的局部應力估算方法，採用該方法估算得到的玻璃螺栓孔處的疲勞壽命與邊緣連接件疲勞試驗結果吻合較好。
  9. Form ties bolt bore : bore drilling should be done when first time used form plate assembling on site to keep away from steel bar and reduce blank out bore happened

    7對拉螺栓孔：第一次使用的模板應在現場組裝就位時鉆孔，以避開鋼筋，減少廢孔的出現。
  10. Bolts are ground and flange holes are calibrated for perfect centering of the two flanges in respect of each other

    螺栓經過打磨，法蘭螺栓孔也經過校準，實現了2個法蘭相互之間的完美對中。
  11. Positioning of moving table for checking screw holes of nuclear reactor pressure vessel

    核反應堆壓力殼螺栓孔檢測自動小車的定位
  12. Aerospace series. holes and traps for t - head bolts design standard

    航空航天系列. t型頭螺栓孔和夾子設計標準
  13. Whether you look to that form of liner plate bolt hole is very special, please see the following picture

    還有一點您注意沒有，襯板螺栓孔形狀很特別，您看下邊這幅圖
  14. Anchor / support bolt holes are located in base of body

    固定器/支架螺栓孔位於閥門的基座。
  15. Collection of from plate should be done before use, do not use deformed and can ' t repair form plate, and abandon bolt hole should be made smoothly

    4模板使用前應進行選材，不能使用變形翹曲且無法修復的模板，廢棄螺栓孔修補平整。
  16. Diameter of the central ring of the bolt

    螺栓孔中心圓直徑
  17. 1 when flanges are integral with fittings or valves, holes for bolts are drilled to straddle the center line

    1如果法蘭與連接件或閥門構成一個整體，則螺栓孔鉆在圓心線兩側。
  18. After the valves are removed ， clean the valve guide bores and all bolt holes ， using a thin brush and solvent

    拆下汽門之後，用一根細刷何溶劑清理汽門導管恐核所有螺栓孔。
  19. Specification of flange dimension and bolt - hole

    法蘭尺寸和螺栓孔規格
  20. Lug body available with iso flange dimensions and metric bolt hole threads

    凸耳式閥體符合iso法蘭尺寸和公制螺栓孔螺紋。
分享友人
分享到 Line

分享到臉書