補償微壓計 的英文怎麼說

中文拼音 [bǔchángwéiyājì]
補償微壓計 英文
compensated micromanometer
  • 補 : Ⅰ動詞1 （修理; 修補） repair; mend; patch 2 （補充; 補足;填補） fill up; add supplement; supply; ...
  • 償 : 動詞1. （歸還; 抵補） repay; compensate for 2. （滿足） meet; fulfil
  • 壓 : 壓構詞成分。
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 補償 : compensate; make up; make up for; make it up to sb. ; make sth. good; compensation; offset
  1. During the period of measurement, the transduction circuits transform the differential pressures, the absolute pressures and the temperatures received by the sensors into the voltage signals, and then, the voltage signals are transformed into digital signals by the a / d convertor. the mcu processes these digital signals and calculates the cumulation of the flow. finally the totalizers contact with the pc by rs - 485 bus to form a distributed measuring network

    在測量過程中，系統以流量計節流所獲得的差壓信號作為主信號、絕壓和溫度信號作為補償信號進行流量積算，這三種信號分別由相應傳感器感知后，經各自的物理信號測量電路轉換為電信號，再由a / d轉換模塊轉變為數字量，交微控制器進行處理、積算。
  2. A compensatory approach to software and hardware used by microprocessor was applied to the intelligent solid pressure transducer, which not only achieved the intelligentization of pressure sensor, but also improved the sensor ' s accuracy. this will surely accelerate the development of instrument towards the direction of multifunction, high degree of accuracy, numeralization, intelligentization, modularization and miniaturization so that measurement system will be further improved

    為此本課題研究固態壓力傳感器的製造技術，通過微處理機的軟體和硬體的補償方法來提高傳感器的精度，實現壓力傳感器的智能化，促使儀表向多功能、高精度、數字化、智能化、模塊化、小型輕量化方向發展，近而得到一個較為完善和理想的測控系統，提出了一種差壓傳感器智能化設計方案。
  3. The combined motor vibration sensor which is held manually with double charge amplifier placed inside and with frequency compensating circuit is designed based on the existed press - electricity accelerator of vibration and the measuring vibration system of charge amplifier in the paper

    本文在現有振動壓電式加速度計、電荷放大器測振系統的基礎上，設計了手持式內置微型雙電荷放大器和頻率補償電路的一體化發動機振動傳感器。
  4. The technology of micro - electronics and calculation method was fully made in the system. how to improve the accuracy of standard orifice measurement is also discussed from the following aspects : the means of measurement and transmitter, online correction of measurement parameter and abnormal condition. all those means are used to overcome its shortcomings of less scale of measurement range, short period of checkout, more tache of maintenance and low accuracy of measure

    該系統充分利用微電子技術和計算技術以及通過實際現場總結的經驗，主要從測量與變送環節採取的措施、相關參數的在線實時補償演算法、非正常情況的在線補償三個方面對如何提高量精度加以論述，盡可能地彌補孔板差壓式流量計量程比較小、檢定周期短、維護環節多、準確度低的不足。
  5. Compensated micro - manometer

    補償微壓計
  6. In view of the problem of signal - to - noise and stability of circuit of photoelectric detection for weak signal, a low - noise amplifier circuit of photoelectric detection is designed, with the functions of filter and phase compensation

    摘要針對光電檢測中對微弱信號放大而帶來的信噪比和穩定性問題，設計了一種低噪聲光電信號放大電路，它具有電壓、電流濾波和相位補償功能。
  7. Verification regulation of standard compensated micro - manometer

    標準補償式微壓計檢定規程
分享友人
分享到 Line

分享到臉書