計件折舊 的英文怎麼說

中文拼音 [jìjiànzhéjiù]
計件折舊 英文
unit depreciation
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  • 折 : 折動詞[口語]1. （翻轉） roll over; turn over 2. （倒過來倒過去） pour back and forth between two containers
  • 舊 : Ⅰ形容詞1 （過去的; 過時的） past; bygone; old 2 （因經過長時間或經過使用而變色或變形的） used; wo...
  1. At last, the paper solves the depreciation problems of the vessel that is sealed up for keeping and port and dock, bringing forward that the parts that are still worn down during the sealed period should be depreciated and the parts having no or less spoilage should not be depreciated according to the theory of parts measurement. the port and dock, able to be wholly renewed through locally overhauling in turn, should apply the method of replacement accounting to process accountancy. xin dawang ( finance and accounting ) directed by professor : shao ruiqing

    上海海運學院jn ：學位論義最後論述了封存船舶和港口碼頭的折舊問題，本文提出：在部件計價基礎上，船舶封存應只對封存時仍繼續損耗的部件計提折舊，其餘未使用或者損耗很小的部件則不計提折舊：港口碼頭可以通過局部輪番大修實現整體更新，每個泊位根據大修制度定期進行大修，等到所有泊位都經過大修以後，則整個碼頭都同新建的碼頭泊位發揮的效用相同，進而應運用重置會計對碼頭固定資產進行會計核算，以正確處理港口碼頭的修理支出以及折舊計提問題。
  2. For overterm service of unit equipment in thermal plant, taking high temperature compression part ( steam pipe ) for example, the paper introduced a three grade appraisal method and calculated the residual life of high temperature compression part using fixed asset linear method, establised a economic life mathematical mode, finally gave out a general economy appraisal for high temperature compression part with a calculation example

    針對火力發電廠機組設備的超期服役，以高溫承壓部件蒸汽管道為例，以其運行工況為基礎，結合材質狀況，逐步實行三級評定，計算高溫承壓部件的剩餘壽命，利用固定資產線性折舊法對設備進行折舊計算，同時建立經濟壽命的數字模型，綜合評定高溫承壓部件的經濟性，並列舉了算例。
  3. With a deep research and analysis of punching part, using manufacturing _ count method, the die cost, punching time, punch selection, punching equipment depreciation cost on the punching process have been evaluated with a mathemetics model established for punching part economic evaluation

    摘要在對沖壓過程進行深入分析研究的基礎上，採用製造計分的方法，對沖壓零件製造過程中模具成本、沖壓時間、沖床選擇、沖壓設備折舊費用進行了評價，建立了沖壓零件經濟性評價的數學模型。
分享友人
分享到 Line

分享到臉書