設計準則 的英文怎麼說

中文拼音 [shèjìzhǔnzé]
設計準則 英文
design criteria
  • 設 : Ⅰ動詞1 （設立; 布置） set up; establish; found 2 （籌劃） work out : 設計陷害 plot a frame up; fr...
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 準 : Ⅰ名詞1 （標準） standard; guideline; criterion; norm 2 （目標） aim; target Ⅱ動詞1 （依據; 依照）...
  • 則 : Ⅰ名詞1 （規范） standard; norm; criterion 2 （規則） regulation; rule; law 3 （姓氏） a surname Ⅱ...
  • 設計 : devise; project; plan; design; excogitation; layout; layout work; styling
  • 準則 : norm; standard; criterion; rule; formula; square
  1. The category, design and guidelines of highway barriers were then described, and dynamics of occupant and injury biomechanics were also discussed. it was found that the most frequently injured body segments during a car - barrier crash are head and thorax, and their injury mechanisms were pointed out

    然後，文章對高速公路護欄的種類、設計方法和設計準則等方面進行了全面討論，同時論述了碰撞過程中乘員的生物力學響應，指出了在轎車-高速公路護欄碰撞中致使乘員受傷最為嚴重的部位和原因。
  2. It brings satisfaction and exciting for the employee, low - cost for the employer and development for the organization. otherwise, the situation will be on the contrary. this paper applies managerial psychology * labor - economics and operations research to analyze the compensation design, the motivation effect of cadi ( chengdu aircraft design and research institute ) synthetically on the basis of introducing the theories about human resource management, compensation and motivation

    本文綜合運用管理心理學、勞動經濟學、運籌學等分析方法，在對人力資源管理、薪酬、激勵等基本理論概括介紹的基礎上，論述了薪酬的分類、決定機制、設計準則及薪酬激勵的模型，探索分析了611所工程技術人員薪酬設計及其激勵效果，分析了現行體制下激勵強度弱等弊端及原因。
  3. Checking code for conformance to design guidelines

    檢查代碼是否符合設計準則。
  4. Through summarization and organization of function principle solutions and contradiction resolving principles, corresponding design rule and database are established in consecution and hierarchy

    通過歸納或整理功能原理解及沖突解決原理，並將其層次化、條理化，建立了相應的設計準則和數據庫。
  5. Abstract : this paper first presents the general design framework of maintenance deployment system in wartime, and then studies the main design criteria : the whole responsiveness, component responsiveness and steadystate efficiency. based on the above, some basic deplyment forms are analyzed and the general design procedure is presented at last

    文摘:給出了設計戰時維修資源設置系統一般框架，提出了設計準則：整體反應性、單元反應性和穩態頻率；並運用以上準則對我軍現實活動中採用的幾種基本部署系統形式進行了分析；最後給出了戰時維修資源部署系統設計的一般程序。
  6. Describes guidelines for designing unsealed classes

    描述未密封類的設計準則。
  7. Based on the kinematical design criterion of equi - chord percent ratio and spatial rigid body guiding mechanism, three theoretical design methods of arc track, non - arc track, and helical track are proposed in this thesis, meanwhile, different design methods about prime flap and sub - flap driving mechanisms are completed. three cases of different three - gaps - fowler - flap tracks are designed

    對后緣三縫富勒襟翼工作時的3個關鍵位置，按照「等弦長百分比」運動的設計準則和空間剛體引導機構的設計思路，提出了圓弧軌道、非圓弧軌道和螺旋線軌道等3種空間位置引導軌道的設計原理，並分別給出主襟翼和子襟翼驅動機構的不同設計方法。
  8. Based on the strength design theory and the practical stress features of the drums and on the phenomenon that the drums produce the circumference stress along the drums under the binding force of the wire ropes and the bending stress along the axis, the paper proposes the fourth strength theory as the basis for the drum strength design

    利用強度設計理論，結合捲筒實際受力特點，針對捲筒體在鋼絲繩緊箍外壓作用下產生沿捲筒徑向、周向應力和軸向局部彎曲應力的情況，提出了以第四強度理論為依據的捲筒強度設計準則。
  9. In addition, the principle for increasing extrusion pressure and determining way for key parameters on each sub - zone was discussed

    通過深入分析，得出了個分區關鍵參數的設計準則與確定方法，探討了提高擠壓力的措施，最後通過與實驗結果的比較驗證了其工程應用價值。
  10. In the second chapter, the fluid mechanics principle of vortex flowmeter at first was introduced. the classical theory about vortex flowmeter and the method of computational fluid dynamics about flow around body were expanded on, and the model of the single bluff body and the dual bluff body vortex flowmeter were constructed. and then, fvm - finite volume method - analysis software fluent was applied to analyze the flow phenomenon of flow over single bluff body or dual bluff body

    然後通過大量實驗和理論分析給出雙鈍體渦街流量計的設計準則：當管徑為d ，鈍體形狀為三角形，則鈍體設計參數為：銳邊寬度= 0 . 26d ，高度= 0 . 34d ，鈍體之間的距離= 1 . 2d （即當兩鈍體寬度相等且鈍體距離等於單鈍體兩列旋渦之間的距離） 。
  11. The influence of separating magnetic flux method of rotor with u ' s and tangential permanent magnet to the pole - to - pole leakage factor is analyzed by finite element method ( fem ), and given the rule of design

    通過對pmsm進行電磁場求解，分析了u型結構和切向結構轉子磁路結構的隔磁措施對電機極間漏磁系數的影響，提出了設計準則。
  12. Abstract : based on the fuzzy mathematics, it establishes the rules of the fuzzy reliability design for the bolt - joint set, discusses the effect of pre - tighten force and the axial changing load on the set, and shows an example

    文摘:將模糊數學理論引入可靠性設計中，考慮預緊力和軸向變載荷狀態的影響因素，建立螺栓聯接的模糊可靠性設計準則，並給出了設計實例。
  13. In chapter 5, by number value simulation calculation and experiment of one simple support beam, we will compare the magnitude of the coupling static and dynamic stress at each point on the girder under harmonic excitation, and so find conclusions such as : ( 1 ) there are so much correlations between structure damage and environmental effect and exterior excitation leads dominant effects in structure damage that we should consider static and dynamic stress together. ( 2 ) new intension design rules should be set up, according which the range of structure possible damage position should be estimated in advance

    得到以下結論： （ 1 ）結構的破壞和環境的影響密不可分，外部激勵在結構破壞中發揮了重要的作用，應該將結構所受的靜力和動力一起考慮； （ 2 ）應該建立新的強度設計準則，並以此作為依據，對已知結構的可能損傷位置有預先的范圍估計，從而為損傷識別的準確定位提供理論依據。
  14. Criteria for design of municipal bridges

    城市橋梁設計準則
  15. Space - time codes can be divided into tree mainly parts : bell layered space - time architecture ( blast ), space - time trellis codes ( sttc ) and space - time block codes ( stbc ). in this paper, we mainly compare the performance of blast and stbc in many aspects, such as design criterion, transmission rate, diversity gain, diversity combining, bit error rate and channel capacity etc. in this paper, we first respectively analysed the instantaneous received symbol energy - to - noise ratio of v _ blast in the diversity combining methods of maximal ratio combining ( mrc ), equal gain combing ( egc ) and selective combing ( sc )

    Mimo技術核心是空時編碼（ stc ） 。空時編碼主要分為三種:分層空時碼（ blast ） 、空時格碼（ sttc ）和空時塊碼（ stbc ） 。本文主要對分層空時碼和空時塊碼這兩種編碼方式在設計準則、傳輸速率、分集增益、接收合併、比特差錯率和通道容量等方面進行了較為詳盡的研究。
  16. Modifcation of strength rules for plate - fin sttucture

    板翅結構強度設計準則的修正
  17. Describes asynchronous programming design guidelines

    描述異步編程設計準則。
  18. Design criteria for consolidation of lwr spent fuel

    輕水反應堆廢燃料壓實的設計準則
  19. Design criteria for supplementary control point of nuclear power plants

    核電廠輔助控制點設計準則
  20. Design criterion of ship fracture control

    海船斷裂控制設計準則
分享友人
分享到 Line

分享到臉書