試液溫升 的英文怎麼說

中文拼音 [shìyèwēnshēng]
試液溫升 英文
samplceleratorytemperature
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 液 : 名詞（液體） liquid; fluid; juice
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 升 : Ⅰ動詞1 （由低往高移動） rise; hoist; go up; ascend 2 （等級提高） promote Ⅱ量詞1 （容量單位） lit...
  • 溫升 : elevated temperature
  1. The omt after its suspension treated with ultrasonic wave was inserted with poly ( styrene - butyl acrylate ) emulsion. xrd test found the layers of omt particles were dispersed partly in the composite ; extraction experiment of nano - omt / pba - st composite indicated a great amount of macromolecule has inserted into the interlayer of omt. dta analysis showed the decompose temperature of composite has improved by 73 at 4 % omt

    將omt的水懸浮液經超聲波處理，與苯丙乳液復合， omt p （ ba - st ）復合物的萃取和xrd試驗證明乳液的大分子已經大量嵌入omt層間，使大部分omt以納米級均勻分散於苯丙乳液之中； dta分析結果說明添加4 omt苯丙復合材料的分解溫度升高了73 。
  2. It was founded that the flux increases as the feed temperature, concentration and flow rate increase, and increases as the downstream pressure decreases. the separation factor increases as the feed flow rate and downstream pressure increase, and decreases as the feed temperature increases

    由試驗結果表明，溫度升高，增大料液濃度，降低冷側壓力，以及增加料液流速，膜蒸餾通量增大；同時流速提高，溫度降低，以及增大冷側壓力，分離因子增大。
  3. The optimum concentration and temperature of dtpmp solution and optimum annealing temperature are discussed. in addition, hydration resistant effect of anodic oxide films treated with adp, atmp and dtpmp respectively is discussed through ft - ir, xps, afm and i - v characteristics testing

    探討了dtpmp溶液濃度、浸漬溫度和熱處理溫度對氧化膜升壓時間、比容、耐電壓的影響，並找到其最佳耐水合處理工藝;同時採用ft - ir 、 xps 、 afm和i - v特性測試對adp 、 atmp 、 dtpmp三種試劑對氧化膜的耐水合處理效果進行了對比研究。
  4. In order to solve the problems that large energy consumption, temperature variation, high, cost trouble maintenance in current electro - hydraulic servo control system for material testing machine, a new design scheme that electro - hydraulic proportional control system for material testing machine based on extension control strategy is proposed. the design scheme is successful by means of designing new main frame system, hydraulic cylinder system, digital electro - hydraulic micro - fluid proportional valve and electrical control system, and its results lay a foundation for material testing machine industries in our country

    針對國內外材料試驗機主要採用電液伺服控制系統，存在能耗大、溫升、成本高、維護困難等問題，本課題提出了基於可拓控制策略的材料試驗機電比例負載適應控制系統這一新型研究方案，通過開發新型試驗機主機系統、液壓缸系統、數字式微小流量電液比例流量閥及電控系統，實現了材料試驗機電液比例負載適應控制，為我國材料試驗機自動控制系統的產業化打下了基礎。
分享友人
分享到 Line

分享到臉書