誤差放大 的英文怎麼說

中文拼音 [wùchāfàngdà]
誤差放大 英文
error magnification
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 放 : releaseset freelet go
  • 誤差 : error
  • 放大 : amplify; magnify; boost; enlarge; blow up; gain; amplification; enhancement; multiplication; magn...
  1. The multi - pass amplifier was being adopted proverbially, which could improve the output energy consumedly. but on the other hand the beam quality was degraded by the severe wave - front ' s aberration that exacerbated by multi - passing the beam through the amplifier

    多程放大系統因能夠較大提高系統的輸出能力，故得到較為廣泛的應用；但由於多程放大級各類波前誤差的相干疊加，使系統輸出激光的波前發生比較嚴重的畸變，導致光束質量的下降。
  2. Therefore, a model of three sectors, respectively referring to domestic sector, manufacturing export sector and primary product export sector, has been established here to measure the technology spillover effects of export on domestic sector. finally, based on a broader framework, this dissertation went on to investigate the relationship between openness and china ' s economic growth, while the result shows that though there exists a notable dispute about how to measure the degree of china ' s openness, the index of trade dependence still maintains the better one to reflect china ' s economic openness. in the meanwhile, impulse response function ( irf ) method and forecasting errors variance decomposition ( fevd ) method, both of which are based on the vector auto - regression ( var ) system, are used here to investigate the dynamic relationship between openness and china ' s economic growth

    與傳統理論不同，新增長理論和新貿易理論都強調技術進步的作用，因此本文構建了一個三部門的技術外溢效應模型（國內部門、工業製成品出口部門以及初級產品出口部門） ，考察了工業製成品出口和初級產品出口對國內非出口部門不同的技術外溢效應；第四，從更加廣闊的視野就貿易開放度與中國經濟增長問題進行研究，有關貿易開放度如何度量一直是存在較大爭議的問題，本文首先對該類研究文獻進行了較為詳盡的述評，然後運用生產函數方法對所選取的5個貿易開放度度量指標進行了檢驗，結果發現盡管一些已有研究認為外貿依存度無法真實度量一國經濟開放水平，但是本文研究結果表明外貿依存度仍是度量我國貿易開放度的較好指標，進一步採用基於var系統的脈沖響應函數法以及預測誤差方法分解法對貿易開放促進經濟增長的作用進行了動態刻畫。
  3. In new system the error pa can also amplify the original signal, so the performance of whole amplifier system increases. since rf predistorters used in the new system, the linearity and power efficiency can be enhanced

    該技術改變了誤差通路中的信號特性，使誤差放大器也輸出有用信號功率，提高了整個放大系統的性能。
  4. The synchronous rectifying and low power sampling technology is used to reduce the power consumption, flexible external loop compensation, error amplifier output clamp are adopted for better system large signal response. the piecewise slope compensation technology is employed to minimize the consequence of over compensation. the sensor resistor is externally connected, which realize output voltage programmable. the overheat protection and under voltage protection modules are integrated in the die to allow the reliable operation of the system

    同時，電路設計採用同步整流技術、低功耗電流采樣技術降低功耗，提高轉換效率;採用靈活的外部環路補償技術、誤差放大器輸出嵌位技術以實現良好大信號特性;採用分段斜坡補償技術，消除不穩定因素，並最大程度地減小過補償帶來的問題;採用外接輸出采樣電阻的方式，實現輸出電壓的可編程。
  5. The functional descriptions of these error mechanisms which can reveal how errors of various blocks in adc affect the output sample are provided ; analyses show that the first stage of the converter is dominant in a pipeline

    首先，通過研究流水線采樣保持電路、子adc 、子dac和殘差放大級的主要誤差機制，用函數表達式將誤差等效到采樣輸出端，量化各部分誤差對系統性能的影響。
  6. Some sub - block circuits ( error amplifier, soft - start, enable comparator and under - voltage protection circuit ) are designed and several electrical characteristics are simulated using hspice. finally, the whole chip performance is simulated. and the results show the satisfaction to both function targets and characteristics

    在子電路設計中，本論文只對其中的誤差放大器、軟啟動電路、使能比較器和欠壓保護四個子電路進行了電路原理分析與設計，並在此基礎上，運用eda軟體hspice對各功能模塊的各項指標、參數進行了模擬、分析。
  7. In the meantime, the all sub - circuits are also designed and emulated carefully including inverter, rs type flip - flop, voltage reference circuit, error amplifier, voltage comparator, sawtooth - wave generator, pwm comparator, soft activation circuit and so on. as a result, all of the sub - circuits answer the requirements. this chip has taped out with the 0. 5um mix - signal process of csmc

    本文利用cadenceeda集成電路設計工具、 spectres模擬工具，對集成電路內的各個模塊包括反相器、基本rs觸發器、基準電壓電路、誤差放大電路、電壓比較電路、鋸齒波振蕩發生電路、 pwm比較電路、軟啟動電路、驅動電路等進行了具體的設計和模擬，且達到了預先設定的指標。
  8. A novel error amplifier with initial voltage reference for series voltage regulator

    串聯穩壓器基準誤差放大電路的設計
  9. Firstly, we improve the algorithm for fast convergence of back propagation by enlarging error in the research of bp network

    首先，在bp神經網路的研究中，對基於誤差放大的快速bp演算法作了改進。
  10. In meantime, the all sub - circuits are also designed and emulated carefully including error amplifier, voltage reference circuit, voltage comparator, rs type flip - flop, soft - start circuit, sawtooth - wave generator, pwm comparator, current added circuit and so on

    其次對控制器內部晶元的各個模塊誤差放大電器、自舉電流電路、電壓基準源、電流求和電路、 rs觸發器和驅動電路等模塊進行了具體的設計和模擬的邏輯功能做了解釋。
  11. And then, based on the above theories, the circuit design and simulation means have been concretely applied in the internal modules of voltage reference, bias circuit, oscillator, error amplifier and drive circuit of the chip and so on. the relevant design indexes are successfully achieved. at last, the whole circuit simulation and layout design are completed

    在此理論基礎上對該電源晶元內部的各個模塊，如電壓基準源、偏置電路、振蕩器、誤差放大電路和驅動電路等模塊進行了具體的電路設計和分析模擬，且達到了相應地設計指標，最後，完成了整體電路模擬和版圖設計。
  12. Consequently, an integrate switch mode power supply with high efficiency and good reliability can be realized by the controller with very few external parts. the fundamental principle of monolithic voltage - mode switching regulator is firstly introduced in this thesis, which is followed by a comparison between voltage - mode and current - mode converters where the pros and cons of both converters are discussed in detail ; next, the global system architecture is proposed upon the design requirements and sub - block circuits are also introduced that focuses on several essential sub - blocks such as amp, wave, pwm control, psc, osc and vref. finally, all sub - circuits and the whole chip circuit are simulated by hspice whose results indicate that the circuit function and performance have perfectly satisfied the design requirements

    在論文中，首先闡述了電壓控制模式pwm開關電源的基本原理，對比了電流控制模式和電壓控制模式，分析了各自的優缺點;隨后根據設計要求進行了電路的總體設計，完成了各個子電路的原理分析，電路設計和模擬驗證，重點闡述了誤差放大電路、三角波發生電路、 pwm控制電路、節能控制電路、振蕩電路和基準源電路的分析、設計和驗證過程;最後，利用eda軟體hspice對整體電路進行了功能模擬驗證，模擬結果表明，本文完成了設計工作，達到設計要求。
  13. Subcircuit models are designed and simulated, which includes bias current source, voltage reference, error amplifier, pwm comparator, driver circuit, protection circuits for over - temperature, over - current. at last, combined with periphery component, the circuit is simulated, and the result meets the anticipant requirement

    並對集成電路內的各個模塊包括電流偏置電路、基準電壓電路、誤差放大電路、三角波振蕩發生電路、 pwm比較電路、驅動電路、過熱保護電路和過流保護等進行了具體的設計和模擬，並對整體應用電路進行了模擬，結果均達到了預先設定的指標。
  14. Connected to the other input of the error amp is the midpoint of a voltage divider. we ' ll come back to this later

    連接誤差放大器另一個輸入點的是一個電壓分壓器的中點電壓。稍後我們再來討論。
  15. The large c1 cap rolls off the gain of the regulator starting at a low frequency so that high frequency noise isn ' t amplified by the error amp

    這個大的電容c1從一個較低的轉折頻率開始滾降，所以高頻噪音沒有被誤差放大器放大。
  16. In order to design the parameter of error amplifier, the small signal model is derived for arc welding inverter using state - space averaging, and frequency - domain analysis is performed to complete the parameter design

    為了設計控制系統中誤差放大器的參數，利用狀態空間平均法建立了電源系統的低頻小信號數學模型，進而利用控制理論中的頻域分析法設計了系統的補償網路，即誤差放大器的參數。
  17. The whole circuit consists of a multiplier, an error amplifier, a comparator, a rs flip - flop, an and gate, and an inverter, etc. the electronic circuit simulator cadence is utilized to practice the detailed functional simulation of the general circuit and the subsystem circuits

    整個電路由模擬乘法器、誤差放大器、比較器、 rs觸發器、與門和倒相器等基本單元電路組成，採用工作站上的大型ic設計軟體cadence進行模擬。
  18. Battery is the only power source for portable equipment. in order to prolong the service time of these battery - operated equipments, ultra - low - power consumption is demanded. the main method that decreases the power losses is to higher the conversion efficiency and to lower the operating voltage

    開關變換器內包含了帶隙參考電壓源、誤差放大器、頻率補償電路、三角波產生電路、 pwm比較器以及數字邏輯控制電路，此晶元採用聯華電子公司0 . 6微米cmos工藝。
  19. In the diagram, the output of the error amp is connected to the base of an npn transistor : when the error amp drives current into this transistor ' s base, it allows current to flow from collector to emitter, and that transistor in turn pulls current from the base of the pass transistor

    在這個圖里，誤差放大器的輸出端連接到了一個npn三極體的基極上：當誤差放大器輸出電流到了三極體的基極上，三極體允許電流從集電極向發射極流動，這個傳輸三極體工作時就是就是從基極吸取電流的過程。
  20. In the thesis, some of the most important functional modules of the pwm power control ics are designed and simulated, including error amplifier, voltage reference, voltage regulator, comparator, and oscillator. the topologies, schematics and layouts of some circuits are introduced and developed

    本畢業設計研究和提出了構成pwm電源控制晶元的主要功能模塊，設計了其中主要模塊ip核的多種結構電路並進行了模擬，完成了部分電路的版圖設計? ?包括誤差放大器，基準電壓源，電壓調節器，比較器，振蕩器等。
分享友人
分享到 Line

分享到臉書