調零裝置 的英文怎麼說

中文拼音 [diàolíngzhuāngzhì]
調零裝置 英文
balancing control
  • 調 : Ⅰ動詞1 (配合得均勻合適) harmonize; suit well; fit in perfectly 2 (使配合得均勻合適) mix; adju...
  • : Ⅰ數詞1 (零數) zero2 (數的空位) zero sign (0); nought 3 (表示沒有數量;無) nil; nought 4 (...
  • : Ⅰ名詞1 (服裝) dress; outfit; attire; clothing 2 (演員的化裝品) stage makeup and costume Ⅱ動詞...
  • : 動詞1. (擱; 放) place; put; lay 2. (設立; 布置) set up; establish; arrange; fix up 3. (購置) buy; purchase
  • 裝置 : 1 (機器設備的配件)installation; device; apparatus; equipment; arrangement; gear; appliance; rig...
  1. Zero governors for gas burners and gas burning appliances ; german version en 12078 : 1998

    氣體燃燒器和氣體燃燒的「"基準調節器
  2. Ventilation for buildings - air handling units - rating and performance for units, components and sections ; german version en 13053 : 2001

    建築物通風.空氣調.元部件和件的額定
  3. In this paper, a new control strategy based on the adaptive deadbeat voltage space vector is presented. this control scheme has a lower sample frequency and a smaller difference between switch frequency and sample frequency. it has many advantages, such as producing zero vectors organically, tracing exactly, non - shaking, etc. and its dynamic response is better

    對于電能質量調節器來講, pwm跟隨指令參考信號的控制性能在很大程度上影響著的補償效果,本文選擇無差拍電壓空間矢量控制為系統控制策略,這種控制方法具有采樣頻率低,開關頻率與采樣頻率的差距小,能有機地產主矢量、跟蹤精確以及無抖振等優點,動態響應快。
  4. ( 3 ) study deeply the structure of fat 16 file system and the characteristic of flash disk, and develop the file management software of flash disk to manage nc files effectively according to the management idea of fat 16 file system. ( 4 ) research the module and protocol of reliable communication in serial network, which are composed of arm main control board, dsp motion control board, keyboard board, i / o control board and encoder signal collection board, and then develop communication software of the serial network. ( 5 ) study the principle of displaying char in lcd and the method of embedding font library into operating system, and research deeply the method of embedding chinese font library into os in the light of the characteristic of chinese

    本論文的主要研究內容如下: ( 1 )研究uc os -實時嵌入式操作系統在硬體平臺上的移植及其佔先式內核的任務調度原理,合理分割銑床控制系統的管理任務,根據任務的要求賦予不同的優先級和調度時間,保證任務的執行效率和實時性; ( 2 )開發底層設備驅動程序和應用程序介面( api )函數,以便於進行系統應用軟體的開發; ( 3 )深入研究fat16文件系統的結構和固態盤的硬體特性,參照fat16文件系統的管理思路,開發固態盤文件管理軟體以有效管理nc代碼文件; ( 4 )深入研究由arm主控板、鍵盤板、 i o控制板、編碼器信號採集板等組成的串口通訊網路可靠通信的模型及其通訊協議,開發串口通訊網路通信軟體; ( 5 )研究字元的顯示原理和在操作系統中嵌入字庫的方法,在此基礎上結合漢字的特性深入研究中文字庫的嵌入方法,開發中文字庫嵌入軟體,滿足開發操作界面的信息要求; ( 6 )深入研究三維圖形坐標變換的原理,開發實用的三維加工軌跡顯示軟體,便於操作者對件的加工過程進行監控和診斷。
  5. The microprocessor is used to realize digital control as flip plus of the scr. the ic chip sa866ae of mitel company is utilized as the low frequency signal generator of the system. furthermore in the zero - current detection circuit, use the photocoupler gaalas ired and photo ic to detect zero - current, furthest shorten the commutating " died region ", prevent the current from distorting

    設計中採用單片機控制可控硅的觸發脈沖,實現數字化控制,並利用mitel公司的三相pwm交流電機脈寬調制晶元sa866ae ,成功研製了交-交頻器中的低頻信號發生器,效果良好;此外利用用光電檢測元件進行系統電流的檢測,盡可能地縮短換相死區,防止電流發生畸變,成功地解決了原有低頻電源系統中存在的兩大難題。
  6. 4 ) the three - dimensional solid models of the spatial cam sliding tooth transmission are built up ; the assembling and exploding on the solid modes of those components are made ; the construction of this transmission device is described directly, and the checkout of the assembling coordination between the components of the spatial cam sliding tooth transmission can be done in the design stage

    4 )建立了空間凸輪活齒傳動的三維實體模型,並對實體模型進行配和爆炸處理,直觀地描述了該傳動的結構,實現了在設計階段對空間凸輪活齒傳動部件配協調性的校驗。
  7. The upper slotting / crease shaft is using automatic plane minor adjustment sysem, also allow roational adjustment of 360 degrees whatever operating or stop. the slotting shaft also using zero - storing system

    上刀軸設平面式自動微調,刻度清晰,不論運轉或停上均可做360相位調整,刀軸及附自動歸
  8. Ease plate change over, zero setting and micro - adjust. plate easily

    版時其歸、微調、換版等作業均能稱心使用。
分享友人