負阻器件 的英文怎麼說

中文拼音 [fùzǔqìjiàn]
負阻器件 英文
negative-resistance device
  • 負 : Ⅰ名詞1 （負擔） burden; load 2 （虧損） loss 3 （失敗） defeat Ⅱ動詞1 [書面語] （背） carry on th...
  • 阻 : 動詞（阻擋; 阻礙） block; hinder; impede; obstruct
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  1. 1 m 0. 5, the phase - shifted angle 6 is controlled in term of sine law which makes the magnitude of resonant voltage track a reference sine voltage, and the resonant voltage is rectified, filtered, inverted and then the better sine - voltage output is obtained, theoretical analysis and experimental results show that for the resistive load and inductive load, the switches of leading leg of the phase - shift - controlled circuit are always turned on at zvs, and ones of lagging leg are turned on at zvs ( < 0 ) or turned off at zcs ( ( > 0 ), moreover, all switches in the low - frequency inverter are always turned on and off at zvs, the measured circuit efficiency for rated load reaches up to 88 %

    從功率單向流動角度出發，提出了一種lcc諧振型恆頻移相單相高頻鏈逆變電路拓撲，在調制系數0 . 1 m 0 . 5情況下，控制移相角按正弦規律變化，使諧振電壓脈沖列的幅值追蹤參考正弦電壓信號，經過整流、濾波、低頻逆變，從而獲得正弦度較好的輸出電壓。理論分析和實驗結果證明對于阻性負載或阻感性負載，移相全橋具有超前橋臂零電壓開通，滯后橋臂或者零電壓開通（ _ 0 ）或者零電流關斷（ _ 0 ）的軟開關特性，而低頻逆變器的各個開關均實現零電壓條件下的開通與關斷。
  2. Power mosfets on - resistance will have a - ve temp coef and not + ve at low current levels. this is important to remember when paralleling devices

    功率mosfets導通電阻有負溫度系數，小電流時有正系數。當並聯這些器件的時候記住以上很重要。
  3. The safety of transmission line plays a important role in power system safety it is not only the requirement of ensure supply power reliability, but also the necessary precondition of enhance power system stabilization, to remove faulty line quickly and accurately, also keep non - faulty line continuous work when some transmission line faults current differential protection is a kind of simple, reliable and good - selective protection manner to any variety of transmission lines, power system development needs current differential protection apply to transmission lines, moreover the advancement of electric and communication technology enable current differential protection apply to transmission lines firstly, the paper discusses, analyses the research and application transmission line protection in detail, compare the principle and realistic presupposition of general line pilot protections secondly, because conventional current vector differential protection are influenced easily by load current and transitional resistance, in order to at the same time quicken protection act, the principle and criterion include work characteristic of differential protect based on fault component sampled values are studied, results shows that differential protect based on fault component sampled values excels general vector current differential protection in reliability, sensitivity and anti - saturation of current transformer in addition, synchronous current sampling methods at all terminals of line is analyzed and estimated lastly, the principle and criterion. also device design about current sampling values differential protection based on optical fiber communication, which apply to short transmission lines are concretely investigated,

    基於基爾霍夫定律的電流差動保護無論對於何種形式的輸電線路都是一種簡單、可靠、選擇性強的保護形式，電力系統的發展使得電流差動保護應用於線路保護成為需要，而電子、通信技術的發展使得電流差動保護應用於輸電線路成為可能。首先，本文對目前線路保護的研究和實際應用情況進行了討論和分析，比較了常用線路縱聯保護的實現原理和實現條件及優缺點。其次，針對常規相量電流差動保護易受正常負荷電流和故障過渡電阻影響的缺點，同時為加快差動保護的動作速度，對基於故障分量瞬時采樣值電流差動保護的原理、判據、動作特性等作了討論和分析，結果表明基於故障分量瞬時采樣值電流差動保護在可靠性、靈敏度、抗電流互感器飽和方面明顯優于常規相量電流差動保護，對電流差動保護各端的同步采樣方法和數據通信也進行了分析和評價。
  4. The exportation resistance of a device work device with what link after loading the resistance s the certain connections for should satisfying, in order to prevent mount to load the appearance produce the obvious influence. with each other connect to say to electronics equipments, for example after signal connect the enlarger, ex - class to connect class, only behind first - degree importation resistance before larger than first - degree exportation resistance 5 - 10 times are above, can think the resistance to match good ; connect the box come saying, electronics tube the machine should choose to use with for the enlarger its output to carry the mark to call the resistance the box for, but transistor enlarger then have noing this restrict, can take officing why resistance of equal or approximate box

    一件器材的輸出阻抗和所連接的負載阻抗之間所應滿足的某種關系，以免接上負載后對器材本身的工作狀態產生明顯的影響。對電子設備互連來說，例如信號源連放大器，前級連后級，只要后一級的輸入阻抗大於前一級的輸出阻抗5 - 10倍以上，就可認為阻抗匹配良好對于放大器連接音箱來說，電子管機應選用與其輸出端標稱阻抗相等或接近的音箱，而晶體管放大器則無此限制，可以接任何阻抗的音箱。
  5. Development of cmos devices and circuits with sub - 0. 1 m gate length

    新型高頻硅光電負阻器件的特性模擬及測試分析
  6. Unified power flow controller ( upfc ) is one of the most powerful and most promising controllers of facts. if we use upfc to control the transmission parameters, terminal voltage, line impedance and phase angle in normal situation and use it to compensate zero sequence and negative sequence currents when one of transmission lines is cut off, we can implement two phases operating in high voltage transmission lines, which can improve stability and reliability for the transmission system

    統一潮流控制器（ upfc ）是功能最強、最具發展潛力的靈活交流輸電系統（ facts ）控制器之一，如果在常規條件下，用upfc實現輸電線路的電壓調節、移相、潮流控制、阻尼振蕩等功能，在發生單相永久性接地或單相斷路故障時，由傳統的三相跳閘改為單相跳閘，用upfc的並補來濾除兩端系統的零序和負序電流，用upfc的串補來提高輸電線的傳輸功率，以實現兩相長期運行，那麼輸電系統的穩定性、可靠性將大大提高。
  7. The pt secondary loop voltage drop is a changing amount and has the characteristics of indirection and certain randomness. the second, according to the cause of pt secondary loop voltage drop, the different methods to reduce the pt secondary loop voltage drop were analyzed and the conclusions are draw as below : 1. changing bigger section wire and maintaining the connector plugs regularly can reduce the pt secondary loop voltage drop effectively, but ca n ' t guarantee which meets the relevant rules

    首先，通過對電壓互感器二次壓降的形成機理進行分析，得出以下關於二次壓降的相關結論： 1 、電壓互感器二次壓降等於二次迴路阻抗和迴路電流的乘積； 2 、電壓互感器二次迴路阻抗分為元器件自身阻抗和接觸阻抗兩部分，且接觸阻抗佔主要部分，從而使得電壓互感器二次迴路阻抗具有動態特性，而且具有一定的隨機性； 3 、電壓互感器二次迴路電流與二次負荷和迴路阻抗大小相關，因而二次迴路電流也是變化的； 4 、電壓互感器二次壓降是一個變化量，且具有單向性和一定的隨機性。
  8. Strain - gauge load cell or force transducer, minimum load impedance 320r

    應變測壓元件或傳感器的最低負載阻抗為320r 。
  9. As a result, this paper gives a corresponding harmonic prevent me asure. finally, according to the asymmetrical characteristics of electrical traction loads, this paper studies the negative sequence currents under different loads and makes a piece of advice for reducing the negative sequence currents produced

    最後，還根據電力牽引負荷三相不對稱的特點，分析了阻抗匹配平衡變壓器在不同負荷條件下的負序電流，對如何減小電力牽引負荷的負序電流提出了一點建議。
  10. The device structure and physical models of 4h - sic mosfet and mesfet are built and the properties are simulated with the use of medici software. the influence of the temperature and structure parameter on the device ' s properties is summarized indicates that no negative resistance exists in breakdown property and the breakdown voltage is up to 85v and 209v separately. the maximum power density of 4h - sic mesfet is as high as 19. 22w / mm. at the same time, the processes of sic field - effect transistor is studied and the fabrication processes suitable to sic mosfet are developed.

    論文分析建立了4h - sicmosfet和mesfet器件的結構模型和物理模型，採用二維器件模擬軟體medici對4h - sicmosfet和mesfet的輸出特性進行了模擬分析，研究了溫度和結構參數對器件特性的影響，表明兩種器件的擊穿特性均沒有負阻現象，擊穿電壓分別達到85v和209v ，由此得到4h - sicmesfet最大功率密度可達到19 . 22w mm ；同時，研究了sic場效應晶體管的製作工藝，初步得到了一套製造sicmosfet器件的製造工藝流程，研製出了4h - sicmosfet器件。
  11. It also gives the motive of the ka - band vco and mixer, associated with the subject ' s requirement and the realistic conditions, according to which a proposal is confirmed that the gunn diode and the varactor are mounted in the same cavity to fulfill the vco and an antiparallel diode pair is used to fulfill the harmonic mixer. in chapter 2, based on the basic theory of negative resistance oscillating, we analyses the gunn oscillator and it ’ s tuning character. chapter 3 introduces the theory of millimeter - wave harmonic mixer

    以此為根據結合課題需要和實驗室的實際條件，確定vco採用耿氏管腔體振蕩器形式，變容管與耿氏管安裝在同一個腔內以進一步減小體積，採用反向並聯二極體實現諧波混頻;第二章介紹負阻振蕩器理論及其調諧原理;第三章介紹毫米波諧波混頻器基本原理;第四章給出了振蕩器及諧波混頻器的設計過程，整個組件聯調的結果;最後是結束語，分析了電路中存在的問題，指出了改進方向。
  12. The mechanical impedance analyzing method utilized, the mathematical formula for the input impedance and transformer ratio of ultrasonic horn are built up, some vibration performance of ultrasonic horns are discussed under different load impedance, the relationship and applicational conditions between the transformer ratio of ultrasonic horn and the radiational impedance are analyzed

    採用機械阻抗分析方法，建立了超聲變幅器的輸入阻抗和變幅比的數學表達式，討論了不同負載阻抗下超聲變幅器的振動性能，分析了超聲變幅器的變幅比與換能器輻射阻抗之間的關系及應用條件。
  13. Otherwise, using the ta buffer layer can effectively reduce the surface roughness. in addition, measured by our measurement system, the polycrystalline the film has similar negative magnetoresistance effect to single - crystalline film, so it is potential to be applied in spintronic devices

    通過磁電子輸運測試系統研究制備的薄膜還發現多晶fe _ 3o _ 4具有同單晶fe _ 3o _ 4類似的負磁電阻特性，因此有望將多晶fe _ 3o _ 4薄膜應用到自旋電子器件中。
  14. Specification for harmonized system of quality assessment for electronic components - blank detail specification : directly heated negative temperature coefficient thermistors beads in solid glass or vitreous enamel

    電子元器件質量評定協調體系規范.空白詳細規范:直接加熱負溫度系數熱敏電阻
  15. Specification for harmonized system of quality assessment for electronic components - blank detail specification : directly heated negative temperature coefficient thermistors beads in envelopes

    電子元器件質量評定協調體系規范.空白詳細規范:直接加熱負溫度系數熱敏電阻
  16. Plus, everything else affects the impedance : the speaker wire, the connections, contributions from crossover circuits inside the speaker, corrosion, fuses and circuit breakers, loading by changing a ported cabinet when you plug or unplug a port insert, condition of the speaker assembly ( like the foam surrounds of a woofer, or the condition of the ferromagnetic fluid of some tweeters ), the cabinet seals, etc

    另外，還有其他東西會影響到揚聲器的阻抗：喇叭線，接線柱，內部分頻線路，部件的腐蝕情況，保險絲或斷路器，箱線頭子和接線柱之間產生的負載，揚聲器組裝時的生產環境，箱體的密封情況，等等。
  17. 30mhz measurement of quartz crystal unit parameters by zero phase technique in a - network ; part 4 : method for the measurement of the load resonance frequency fl load resonance resistance rl and the calculation of other derived values of quartz crystal units, up to 30 mhz

    用型網路的零相位技術測量石英諧振器參數.第4部分:石英晶體元件負荷諧振頻率fl負荷諧振電阻rl的測量方法，以及石英晶體元件其他導出值的計算方法
  18. The second, the realization of the zvs has no concerned with the attribute of load. with the load of light or full, even the resistance or inductor load, the chopper can ensure that the main - switches will realize the zvs switching

    其次，實現零電壓軟開關的條件與負載的性質和程度沒有關系，無論是電阻性負載還是大電感負載，無論是輕載還是滿載，都可以實現功率器件的零電壓開通和關斷。
分享友人
分享到 Line

分享到臉書