超范圍修理 的英文怎麼說

中文拼音 [chāofànwéixiūlǐ]
超范圍修理 英文
repair beyond the scope of repairing course
  • 超 : Ⅰ動詞1 （越過; 高出） exceed; surpass; overtake 2 （在某個范圍以外; 不受限制） transcend; go beyo...
  • 范 : 名詞1 [書面語] （模子） pattern; mould; matrix 2 （模範; 榜樣） model; example 3 （范圍） boundar...
  • 圍 : Ⅰ動詞1 （四周攔擋起來 使裡外不通; 環繞） enclose; surround; corral 2 （繞; 裹） wrap Ⅱ名詞1 （四...
  • 修 : Ⅰ動詞1 （修飾） embellish; decorate 2 （修理; 整治） repair; mend; overhaul 3 （寫; 編寫） write;...
  • 理 : Ⅰ名詞1 （物質組織的條紋） texture; grain （in wood skin etc ） 2 （道理;事理） reason; logic; tru...
  • 范圍 : scope; limits; extent; boundary; confines; range; range dimension; spectrum
  1. With the reference of many relevant materials, the author prepared a fined molybdenum disulfide powder with a average size of 800nm by ball milling, and a nano - copper with average size of 30nm in micromulsion solution method, and synthesized surface - modified titanium dioxide nanoparticles with average size of 40nm in organic media via sol - gel method. the tribological performances of three particles were studied by universal test as well, with the result of fined molybdenum disulfide powder with good reducing wear and antiwear performance at low load, nano - copper with good reducing wear and antiwear performance at high load, surface - modified titanium dioxide nanoparticles maintaining stable reducing wear and antiwear performance from low load to high load due to its characteristics of organic and inorganic nanocomposite. the results indicate that the nanocomposite is the most perspective oil additive. the reducing wear and antiwear mechanism of nano oil additive was studied with in - situ tribochemical principle. nano additives possess broadly developing prospect with its above - mentioned performance

    在參閱了大量文獻的基礎上，分別採用了球磨法、微乳液法、溶膠?凝膠法制備了超細二硫化鉬、納米銅粒子、表面修飾納米二氧化鈦，經原子力顯微鏡測試，獲得的超細二硫化鉬的粒度平均在800nm以內，納米銅粒子平均粒度約為30nm ，表面修飾納米二氧化鈦平均粒度約為40nm ，在萬能摩擦磨損試驗機上測試了三種粒子的摩擦學特性，結果表明：在合理的添加濃度范圍內，超細二硫化鉬在低載時具有優良的減摩抗磨性能，納米銅在高載時具有比較好的減摩抗磨性能，表面修飾二氧化鈦粒子因具有有機與無機復合物的特性，從低載到高載都保持穩定的減摩抗磨性能。
  2. By it, the temperature and axial displacement on axes around the blades of the turbine can be measured. the advanced circuits monitor their change. if the temperature and displacement go beyond the normal range, the alert will be sent out, and they can be stopped and repaired " at that time

    渦輪機的工作環境惡劣，為克服環境給測量帶來的困難，採用非接觸式測量方法對渦輪機軸的溫度和渦輪機軸的軸向位移進行測量，採用精確的電路監控溫度和位移的變化，若溫度和位移超出其正常工作范圍，立刻發出警報，停止其工作以進行及時的修理。
  3. This paper introduces some kinds of super - abrasive grinding wheel dressing method swidely used in ultra - precision grinding, analyses their principle, characteristic and extension

    論述了超精密磨削中廣泛應用的幾種超硬砂輪修整技術，分析了它們的工作原理，特點和適用范圍
分享友人
分享到 Line

分享到臉書