軋制道次 的英文怎麼說

中文拼音 [yàzhìdàocì]
軋制道次 英文
rolling pass
  • 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 道 : Ⅰ名詞（道路） road; way; route; path 2 （水流通過的途徑） channel; course 3 （方向; 方法; 道理） ...
  • 次 : Ⅰ名詞1 （次序; 等第） order; sequence 2 [書面語] （出外遠行時停留的處所） stopping place on a jou...
  1. Rolling - cutting biscuit shaping machine is new equipment of making soda biscuit, good toughness of thin biscuit and super - thin biscuit. it ' s high production efficiency, low noises, safe operation, convenient, beautiful outer shape. this machine can press and roll rough flour 3 times and equiped with remaining flour recycling machine, also equiped with double - rolling cutting shaped equipement, in the mean time, it can produce two biscuit embryo of differnt shape. 3 times pressing - rolling machine can adjust different thickness and biscuit rough surface. it can roll rough flour and do not stick to rough flour embryo, correctness rate of adopting mould to cut margin of flour embryo reaches 100 percent so that avoid deforming of embryo due to deviation. this machine is one equipment which adopting advanced and won first technical rewarding for its independently control operation, beautiful outer appearance

    滾切式餅干成型機是連續製作梳打餅、韌性和薄餅超薄餅的新型設備，具有生產效率高、噪音低，操作安全、方便，外型美觀等優點，本機具有三道軋輥制皮和余料回收機，配備雙滾切成型裝置，同時能生產兩種不同形狀的餅干胚不停機，三道軋輥能同時調節不同厚度和餅皮具有軋輥不粘皮、採用印模切邊一次同步進行準確率100 % ，避免偏差而造成餅胚變形，該機具有獨立控制操作，外形美觀，是目前國內較先進而獲得技術一等獎的設備。
  2. And it investigates the appearance condition ( including joint, crack, eroding, corrosion, braking pole device rupture, crane - girder ' s gnawing railway and so on ) of the whole crane - girder system on the spot, at the same time, it also actually examines the stress of the beam, chemical ingredient, distortion and railway excursion, etc. through sampling, and based on the actually examined results, it checks and calculates the carrying capacity of crane - girder system. then, based on the investigating on the spot and the calculated result, it discusses the mechanism of fatigue failure of the upper part of welded steel crane - girder, analyses the reason of steel crane - girder in the high - frequency emerging the fatigue crack, institutes the strengthened method of damaged steel crane - girder of accurate packing up workshop of the primary mill plant. finally, it presents some advice and suggestions for the repairing and strengthening method of fatigue crack of upper part of steel crane - girder in the high - frequency

    針對包鋼初軋廠精整車間鋼吊車樑上部區域出現裂縫這一問題，本文首先綜述了國內外關于焊接鋼吊車樑上部區域疲勞裂縫的研究現狀；其次對整個吊車梁系統的外觀情況（包括連接、裂縫、腐蝕、銹蝕、制動桿件斷裂、吊車啃軌等）進行了現場調查，抽樣實測了梁的應力、化學成分、變形及軌道偏移等，根據實測結果，對吊車梁系統的承載能力進行了驗算；然後，根據現場調查及計算結果，探討了焊接鋼吊車樑上部區域疲勞破壞的機理，分析了重級工作制鋼吊車梁出現疲勞裂縫的原因，制定了初軋廠精整車間破損鋼吊車梁的加固方案；最後就重級工作制鋼吊車樑上部區域出現疲勞裂縫的修復與加固方案提出了一些意見和建議。
  3. The explicit finite element method ( fem ) based on the varying time - step was selected to analyse the dynamic roll - pass process ; the nodes on the leading face of the steady - state elements set was extracted and projected onto a plane to give the required mesh, also called the origin mesh ; the implicit fem was selected to analyses the inter - pass transient thermal process ; a geometric part from the mesh was generated and meshed by using the quadrilateral elements, a heat transfer analysis was selected to transfer the node temperature data ; a new model was created by using hexahedral elements, mapping the node temperature and the equivalent plastic strain on the integration points

    利用基於變步長中心差分格式的顯式積分方法分析瞬態軋制過程；提取穩態單元集節點形成截面網格；利用隱式積分方法分析軋制道次間隙瞬態溫度場；對型鋼斷面進行平面四邊形網格劃分並映射節點溫度數據；利用六面體單元構建有限元分析模型，映射單元節點的溫度、積分點的等效塑性應變，進行數值分析。
  4. It can also create micro cracked edges if the speed is forced to remain higher, which can create quality concerns downstream during following passes

    如果強制保持較高軋制速度，則也會導致微裂邊，從而對后道次加工過程中的下游工序造成質量問題。
  5. The research of the influence of gap setting precision on finishing plate size precision shows that the sensibility of finishing size precision to gap setting precision of the first several passes is low

    摘要分析中厚板軋制過程不同道次輥縫設定精度對軋件終軋尺寸精度的影響，證明了軋件終軋尺寸精度對前面道次的輥縫設定精度不敏感。
  6. This method can decrease the gap setting time for which the oil column of hydraulic cylinder is not retracted and there is no minute adjustment of oil column for the first several passes

    採用該方法，軋制過程液壓缸油柱不用回縮，而且前面道次液壓不進行微調，從而節省了輥縫設定時間。
  7. The results show that the bonding is good when the temperature, two passes deformation ratio of rolling are 1 250 c, 50 % respectively

    結果表明；軋制溫度為1250c 、兩道次的軋制變形率為50 %時，界面結合較好。
分享友人
分享到 Line

分享到臉書