軋延 的英文怎麼說

中文拼音 [yàyán]
軋延 英文
stripmill
  • 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
  1. This research job analysised the extending roll pass system the finish roll pass system and the ultimate roll groove. the mathematical models and experience formulations used for roll pass design are corrected according to the basic theory and the practical experience of the engineerings. the thread steel bar card was set up with the visual program tool - visualbasic6. 0, based on the method of the structural program design

    本課題通過對螺紋鋼延伸孔型系統、精軋孔型系統及成品孔型的構成和設計方法的分析，結合螺紋鋼孔型系統的基本設計理論和工程技術人員的實際生產經驗，對以往孔型設計過程中所使用的數學模型、經驗公式等進行了修正，以結構化程序設計方法為基礎，採用可視化編程工具visualbasic6 . 0建立了螺紋鋼計算機輔助孔型設計系統。
  2. Water is also used as a coolant for rolling - mill roll to maintain their contour and lengthen their service life

    熱軋機的軋輥也需用冷卻水來保持軋輥的外形和延長它的使用壽命。
  3. The casting fogging extrusion rolling steel

    鋼材的熔鑄鍛造擠壓及延軋
  4. Abstract : based on the mathematical models of roll speed for cross - rolling elongation process, the effects of toe angle on roll speed, local feed angle and local angular velocity, and also on material flow are analyzed. by the analysis, the toe angle can be optimized

    文摘:基於建立的斜軋延伸機軋輥速度模型，模擬分析了沿軋制方向和螺旋方向上輾軋角對軋輥速度、局部送進角、局部角速度的影響，進而分析了這些參數對金屬變形和流動的影響，據此可優化輾軋角。
  5. Offers cesium metal and compounds, sophisticated zirconium, titanium and barium metal powders, hydrides and metal alloys as well as minor metals for the manufacture of special alloys

    -鋼鐵冶煉鋼材軋制其他金屬冶煉及其壓延加工銷售，燒結礦焦炭化工產品的生產電子產品機械冶金設備製造。
  6. Tin mill products, electrolytic tin plate, double reduced metric

    錫軋製品.二次壓延的電解鍍錫板
  7. Tin mill products, electrolytic tin plate, single reduced metric

    錫軋製品.一次壓延的電解鍍錫板
  8. Polypropylene spun - bonded fabric product line, geotextile compound film product line, single - layer / multi - layer co - extruded cast embossed film unit, running compound film machine, large - size film coating machine, laminator, hot - rolling mill of non - woven fabrics, splitting machine

    聚丙烯紡粘非織造布生產線，土工布復合生產線，單層/多層共擠流延壓紋膜機組，流延膜機，大型塗膜機，淋膜機，熱軋機，分切機
  9. Firstly, the distortion of rolled piece and the designing method in the beforehand slit pass and slit pass has been analyzed. secondly, based on the research production of predecessor and research of the author, card system selected some corresponding experience formulas such as roll force, roll moment, roll temperature and roll consume, and established spread model in the beforehand slit pass and slit pass and the distribution model of elongation coefficient. subsequently, card system applied the dynamic programming method with minimum roll consume and optimized its pass system

    本文以圓鋼雙線切分為基本實體模型，著重分析了預切分孔型和切分孔型在軋制過程中的變形特點及相應的孔型設計方法；基於前人的研究成果及作者的探索，選擇了相應的軋制力、軋制力矩、溫度及能耗模型，建立了預切分和切分的寬展及延伸系數的分配模型；應用動態規劃法以能耗最小為目標函數對孔型系統進行了優化設計；利用visualbasic6 . 0和microsoftaccess數據庫的連接，建立了數據查詢系統，以visualbasic6 . 0和autocad之間的介面在vb環境下完成了斷面孔型圖的繪制。
  10. The rolled products project experienced some initial delay owing to adverse weather conditions and prolonged negotiations over some design and engineering contracts

    鋁軋制產品項目開展初期，由於天氣狀況欠佳，加上在設計及工程合約上的洽商出現了延誤，故施工期早段有所延誤。
  11. Abstract : effects of mixed re metals on the properties of low oxygen cleaned round copper rods manufactered by continuous casting and rolling were studied. it shows that trace re elements improve not only the elongation of the rods significantly but also the conductivity, meanwhile, reducing the oxygen contents in the material. in consequence, the product grade is raised from grade 2 to grade 1, and the final products are improved to higher - grade

    文摘:研究了混合稀土金屬對連鑄連軋生產的低氧光亮圓銅桿性能的影響.結果表明，添加微量稀土元素不僅能明顯提高材料的延伸率，而且還提高了其導電性能，同時降低了材料中的氧含量，性能指標從原來的2級品上升為1級品，從而提高了最終產品的檔次
  12. The push down scale were wildly using, the best one was 0. 25mm and it also found that the density of the sample all boost

    分別採用不同的壓進量進行軋制，結果發現壓延後樣品的密度都有一定的提高， 0 . 25mm壓進量效果最好。
分享友人
分享到 Line

分享到臉書