載幅調整 的英文怎麼說

中文拼音 [zǎifúdiàozhěng]
載幅調整 英文
carrier-amplitude regulation
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 幅 : Ⅰ名詞1. （布帛、呢絨等的寬度） width of cloth 2. （泛指寬度） width; size 3. （姓氏） a surname Ⅱ量詞（用於布帛、呢絨、圖畫等）
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 整 : Ⅰ形容詞1 （全部在內; 完整） whole; all; complete 2 （整齊） neat; tidy; orderly Ⅱ動詞1 （整理; 整...
  • 調整 : adjust; tune up; trim; trimming; variation; modulation; arrangement; debug; rectification; redres...
  1. 1 m 0. 5, the phase - shifted angle 6 is controlled in term of sine law which makes the magnitude of resonant voltage track a reference sine voltage, and the resonant voltage is rectified, filtered, inverted and then the better sine - voltage output is obtained, theoretical analysis and experimental results show that for the resistive load and inductive load, the switches of leading leg of the phase - shift - controlled circuit are always turned on at zvs, and ones of lagging leg are turned on at zvs ( < 0 ) or turned off at zcs ( ( > 0 ), moreover, all switches in the low - frequency inverter are always turned on and off at zvs, the measured circuit efficiency for rated load reaches up to 88 %

    從功率單向流動角度出發，提出了一種lcc諧振型恆頻移相單相高頻鏈逆變電路拓撲，在調制系數0 . 1 m 0 . 5情況下，控制移相角按正弦規律變化，使諧振電壓脈沖列的幅值追蹤參考正弦電壓信號，經過整流、濾波、低頻逆變，從而獲得正弦度較好的輸出電壓。理論分析和實驗結果證明對于阻性負載或阻感性負載，移相全橋具有超前橋臂零電壓開通，滯后橋臂或者零電壓開通（ _ 0 ）或者零電流關斷（ _ 0 ）的軟開關特性，而低頻逆變器的各個開關均實現零電壓條件下的開通與關斷。
  2. In ciefcm, a tiny disturbance was added to filial generation group by using chaos variable and the disturbance amplitude was adjusted step by step, which greatly improves the colony diversity of immune evolution algorithm ( tea )

    該演算法把混沌變量加載于免疫演算法的變量群體中，利用混沌搜索的特點對群體進行微小擾動並逐步調整擾動幅度，明顯改善了免疫演算法的群體多樣性。
  3. So, for the design of prestressed frame, the later coefficient may be considered as the parameter of modulation of moment and the moment modulated is the moment caused by the vertical load plus the one by the horizontal load

    因此，在預應力框架設計中，可以取只承受豎向荷載的彎矩調幅作為其調幅標準，調幅彎矩為豎向荷載產生的彎矩與水平荷載產生的彎矩之和，即用最小的彎矩調幅系數來調整截面的彎矩。
  4. The characteristics of the intrinsic frequency distribution of the framed steam turbine - generator set foundation are summarized ; it can been seen that the base plate of the framed foundation does not have much effect on the dynamic response of the foundation, and that the " amplitude method " is better than the " resonance method " among dynamic analysis methods. when designing a framed foundation, as long as the load - bearing capacity and stability is ensured, a flexible pillar is better, the amplitude of vibration can be controlled through adjusting the particle quality in foundation design

    論文最後總結了框架式汽輪發電機組基礎固有頻率的分佈特點；指出框架式基礎底板本身對基礎的動力響應影響不大，認為動力分析方法中振幅法優于共振法；並指出框架式基礎設計時，在滿足承載力和穩定性的前提下，柱子應以柔為佳；設計中可以通過調整質點的質量來達到控制基礎振幅的目的。
  5. Throw the research we can get the performance of the joint of the unbond precast and pretressed continuous beam and how the moment redistributes. we got the conclusion that compare the monolithic prestressed continuous beam, the unbond precast and pretressed continuous beam has short amplitude modulation capacity

    得到預制預應力連續梁接縫處的受力性能，內力重分佈的表現形式，並認為在極限荷載下預制預應力連續梁的調幅能力低於整澆式連續梁等特性。
  6. By way of these tendons, precest beams and columns can be assembled conveniently, and the joints and frame are monolithic and continuous. consequently, compared with common reinforced concrete frams, this kind of frame systems possess higher reliability and solved the problems in the process of assembling prestressed concrete frames. also it forms the framework of subassemblage and prestressed concrete frames, and explores a new way for industrial production of prestressed structures. by analyzing this system, a series of conclusion are provided, incluing modulation of bending moment produced by vertical loads within beam end, secondary internal forces produced by pretress force, shear resistance of the end of beams, the influence of lateral restrains. theresearch results of this paper are proved to be practical. some advices are also brought forward on the design process

    后張預應力筋既可作為施工階段拼裝手段，又可在使用階段承受梁端彎矩，構成整體受力節點和連續受力框架，克服了裝配式節點受力可靠性差的缺陷，解決了預應力混凝土框架難以裝配的問題，形成預制預應力混凝土裝配整體式框架，開辟了預應力結構工業化生產的新途徑。本文針對預壓裝配式預應力混凝土框架，從豎向荷載作用下的梁端彎矩調幅、施加預應力在框架中產生的次內力、梁端抗剪承載力、考慮側限的無側移框架的承載力分析四個方面對該種裝配式結構體系的性能做了詳細的研究。
分享友人
分享到 Line

分享到臉書