輪齒平行度 的英文怎麼說

中文拼音 [lúnchǐpínghángdù]
輪齒平行度 英文
parallelism of teeth
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 平 : Ⅰ形容詞1 （沒有高低凹凸 不頃斜） flat; level; even; smooth 2 （高度相同; 不相上下） on the same l...
  • 行 : 行Ⅰ名詞1 （行列） line; row 2 （排行） seniority among brothers and sisters:你行幾? 我行三。where...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. This drilling adopts crank connecting link and walking beam percussion mechanism, which make the drilling possess two percussive functions, normal drilling takes connecting link impact as main mode, when encountering special situation and the connecting link impact can not drill, it can transform into hoisting impact, the stroke length can be modulated, it realizes automatic percussive drilling due to continuous operating of connecting link percussive mechanism, these can enhance drilling efficiency and relieve labor intensity ; it adopts pumping reverse circulation to drain slag, which not only resolves the drilling difficulty in special stratum such as pebble and gravel stratum and hard stratum, but also resolves the problem that the percussive drill ' s efficiency is low ; it adopts spur gear differential mechanism as double cylinders lazy tongs of main hoist, which not only ensures the balance state of drilling tool, but also reduces the mechanical design, and reduces the cost ; the bottom plate traveling motion of this drilling machine adopts walking type ; the drilling tower adopts hydraulic pressure uprising, and reduces the assistant operating time

    該鉆機採用曲柄連桿、游梁式沖擊機構，使鉆機具有兩種沖擊功能;正常鉆進以連桿沖擊為主，遇到特殊情況，用連桿沖擊不能鉆進時，可轉為卷揚沖擊，沖程可調，因連桿沖擊機構連續工作，所以實現了自動沖擊鉆進，可提高鉆進效率，減輕勞動強度;採用泵吸反循環的方式排渣，既能有效解決卵礫石地層、堅硬地層等特殊地層鉆進的困難，又很好地解決了沖擊鉆機效率低下的問題;採用直齒圓柱齒輪差速機構作為主卷揚的雙筒同步機構，既保證了鉆具處于平衡狀態，又大大簡化了該機構設計，降低了成本;該鉆機底盤行走移位採用步履式;鉆塔採用液壓起立，減少了輔助作業時間。
  2. Finally, in consideration of the characteristics of the differential balance mechanism, a more accurate virtual prototype of the mechanism is established and the simulation is carried out in the software environment of adams. the angular velocity curves of the relevant parts and the natural frequency of the mechanism are got. the results may be helpful to the improvement and the application of the mechanism

    最後，綜合考慮了輪齒嚙合剛度、搖臂軸扭轉柔性及齒輪傳動回差對差動平衡機構的影響，建立了能夠比較完整地反映該機構動態特性的虛擬樣機模型;在adams軟體環境下，對差動平衡機構的虛擬樣機模型進行了動態模擬，得出了能反映該機構動態特性的關系曲線，並確定了其固有頻率，為該機構的改進及其在月球車上的實際應用提供了參考依據。
  3. According to the high precision and rotation stability requirement of negative scan unit of cylinder photography typesetting machine, the three levels of cylindrical gears transmission separately, the two - stage cylindrical gears - worm drive, and the worm drive was chosen through calculating its velocity ratio, the checking transmission precision, carrying on the movement precision analysis to the sweep unit, and computing overall transmission error

    摘要針對圓筒型照相排版機底片掃描裝置要求傳動精度高，轉動平穩的特點，分別選擇三級圓柱齒輪傳動，雙級圓柱齒輪蝸桿傳動，蝸桿傳動3種常見的傳動方式，計算其傳動比，驗算傳動精度，對掃描裝置進行運動精度分析，計算總體傳動誤差。
  4. Cylindrical gears - code of inspection practice - recommendations relative to gear blanks, shaft centre distance and parallelism of axes

    圓柱齒輪.檢驗實施標準.與齒輪坯料，軸心距和軸的平行度相關的推薦值
  5. Establishing a close partnership with tianjin huashengchang gear company, we can produce the plane enveloping toroidal worm reducer with a high accuracy and a high productivity which has high efficiency in transmission and less noise and stable operation

    我們由於提供了靈活的生產方式和天津華盛昌齒輪公司的長期合作，因此可以生產出高精度，高效率雙包絡面蝸桿渦輪副的客梯用曳引機系列產品，其特點是傳動效率高，在噪音低，運行平穩可靠，可與進口曳引機相媲美。
  6. The curvature interference of the gear and the influence of radius of the mill - cutter, axial misalignment, and center distance on meshing are analyzed. based on these analyses, propose two methods to achieve point - contact : to change the radius of the mill - cutter and increase the center distance

    在分析了弧齒線圓柱齒輪的嚙合傳動不產生曲率干涉的條件和刀盤展成半徑、軸線平行度誤差、中心距對嚙合影響的基礎上，提出了點接觸弧齒線圓柱齒輪實現的兩種方案:調整刀盤展成半徑和增大中心距。
  7. Cylindrical gears - code of inspection practice - part 3 : recommendations relative to gear blanks, shaft centre distance and parallelism of axes

    圓柱齒輪檢驗實施規范第3部分:齒輪坯軸中心距和軸線平行度
分享友人
分享到 Line

分享到臉書