輪齒接觸分析 的英文怎麼說

中文拼音 [lúnchǐjiēchùfēnxī]
輪齒接觸分析 英文
tooth contact analysis
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 析 : Ⅰ動詞1. （分開; 散開） divide; separate 2. （分析） analyse; dissect; resolve Ⅱ名詞（姓氏） a surname
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  1. Analyse the tooth contact analysis of klingelnberg cyclo - palloid spiral bevel gear

    對克林貝格擺線齒錐齒輪進行齒面接觸分析。
  2. Analyze the stresses distributing of helical gear in long direction using 3dcbem. optimize the shape of dentiform using cvm as the optimize algorithm. the result were satisfied

    作者編制了斜齒輪前處理程序，應用邊界元應力分析程序3dcbem分析了沿齒寬方向的輪齒接觸應力的分佈。
  3. In order to solve the problems of which the spiral bevel gear of oerlikon type is necessary to out and modify repeatedly, a new method was developed to predict the contact pattern and greatly reduce the cost for manufacturing by means of building a tooth contact analysis model of prolate epicycloids bevel and hypoid gears for oerlikon skm2

    摘要為解決奧利康錐齒輪加工過程中需要反復試切、修正的問題，根據奧利康skm2機床建立了加工延伸外擺線齒錐齒輪和準雙曲面齒輪的齒面接觸分析模型，提出了一種可預測齒面接觸質量、降低設計加工成本的新方法。
  4. 3. studying on prediction methods of the initiation life of aero - gear using shakedown analysis methods in order to directly consider in a quantitative way the details of stress - inelastic strain responses, residual stress and residual strain computations, fatigue crack initiation life was evaluated in aero - gear by using th

    利用chaboche的材料模型，研究了航空齒輪韌性材料在彈、塑性安定下的輪齒接觸疲勞裂紋萌生準則，該研究結果與相關的齒輪實驗結果比較分析表明：塑性安定下的疲勞裂紋萌生預測方法預測航空齒輪的萌生壽命是較安全的。
  5. Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3

    通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3
  6. Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance

    根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2
  7. Numerical analysis of instantaneous elestohydrodynamic lubrication in point contact of spiral bevel gear with high speed

    高速弧齒錐齒輪點接觸瞬態等溫彈流數值分析
  8. This paper mainly discussed the optimization design of two - stage star - type gear transmission system. it covered the two sides : one - stage gear transmission and two - stage gear transmission. on the basis of their analysis and research, the mathematic models are created which include the objective functions of minimum volume and minimum center distance, the constraints of contact strength, bend strength and scuffing strength

    本文主要研究了航空發動機星型齒輪傳動系統的優化設計，對單級齒輪傳動和兩級星型傳動都進行了深入的分析和探討，分別以系統體積最小和中心距最小為目標函數，以齒輪的接觸強度、彎曲強度、膠合強度等為約束條件，建立了完整的數學模型。
  9. Through systemic analyzing on spiral helical gear transmission with different basic parameters, the essay found out rules of how can such basic parameters influence spiral helical gear engagement characteristics. so it brings forward the auxiliary assembling mode of adopting one straight gear and one helical gear on condition of little axial angle as well as treasures to ameliorate ill engagement performance on condition of large axial angle, another two jobs of the essay are to clarify the wrong concept that spiral helical gear can only transmit movement but not impetus and to provide a brief and practical method of analyzing contact for gear pairs whose surface equations can be written out directly

    通過對不同基本參數的螺旋齒輪傳動進行系統研究，找出了螺旋齒輪基本參數對其嚙合特性的影響規律，提出小軸交角條件下可採用一直齒輪、一斜齒輪的齒輪副組合方式，給出了大軸交角條件下嚙合性能不良的改進措施。澄清了螺旋齒輪只能傳遞運動不能傳遞動力的誤區，為能夠直接寫出齒面方程的齒輪副進行齒面接觸分析提供了一種簡便、實用的新方法。
  10. Based on the theories of gear engagement, contact analysis, friction and heat transfer, a three - dimensional finite element model of gear tooth was established to investigate temperature distributions and variations along the contact path over a range of applied loads and operating speeds with consideration of lubrication conditions. sensitivity analysis of surface temperature to gear configuration, frictional heat flux, heat transfer coefficients, and oil and ambient temperature was conducted and the major parameters influencing surface temperature were evaluated

    本文基於齒輪嚙合原理、輪齒接觸分析、摩擦學和傳熱學，以有限元分析方法和理論分析計算相結合為手段並以實驗測量結果作為參考，建立了適用於工業應用並具有較高計算精度的高速齒輪傳動輪齒溫度分析的模型和方法，系統地分析了輪齒本體溫度的大小和分佈以及齒輪幾何、載荷及轉速和潤滑冷卻條件等對輪齒本體溫度的影響。
  11. Firstly, a simple and practical representing method of the tooth edge tangential vector is applied to replace the traditional differential formula, the simple solving technique of edge contact problem makes the geometric edge contact analysis of the complex curve surface realize. secondly, using numerical searching and mathematical programming method solves the contact directions and loaded contact problem. finally, whole numerical simulation method is provided for loaded tooth contact analysis of high contact ratio spiral bevel gears

    首先以一種簡單實用的輪齒邊緣切矢量的數學表示方法取代了經典的微分表達式，大大簡化了幾何邊緣接觸的求解，使復雜曲面的幾何邊緣接觸分析得以實現；其次又採用數值搜索與數學規劃法求解了邊緣接觸的主方向和承載接觸問題，為高重合度弧齒錐齒輪承載嚙合全過程的數值模擬提供了完整的方法。
  12. Tooth contact analysis

    輪齒接觸分析
  13. An aeroengine power - turbine 1 ( superscript st ) stage rotor shrouded blade is taken for an example in the article, tightness of shroud and contact force 、 blade body stress under working state and assembly state are calculated by finite element contact analysis method, influence of working load ( temperature and centrifugal force ) is mainly analyzed

    摘要以航空發動機動力渦輪一級帶鋸齒形葉冠的轉子葉片為例，用有限元接觸分析方法對裝配和工作狀態下的葉冠緊度和葉冠接觸力、葉身應力進行了計算和分析，著重考察了工作載荷（溫度和離心力）對葉冠接觸力的影響。
  14. Edge contact analysis method and simulation of klingelnberg spiral bevel gear

    擺線錐齒輪邊緣接觸分析與模擬研究
  15. A new method for loaded tooth contact analysis of spiral bevel gears with friction

    弧齒錐齒輪的有摩擦承載接觸分析
  16. The mathematical model of loaded tooth contact analysis of spiral bevel gears has been established based on elastic dynamics and the dimensional finte element analysis method

    基於彈性力學和有限元法，建立了螺旋錐齒輪加載接觸分析的數學模型。
  17. 3 、 based on the model, a quasi - static meshing simulation is carried out in a meshing period. the numerical results which indicating the variety of the contact status, the contact stress, the bending stress in the location of teeth root and the torque and rotary speed of gear pair vs. the different meshing position are presented, and the rationality of the model is be verified

    3 、基於所建有限元分析模型，在一個嚙合周期內，對齒輪副進行準靜態嚙合模擬分析，給出了準靜態嚙合時齒輪的接觸狀態、接觸應力、齒根彎曲應力及主從動齒輪的扭矩和轉速隨嚙合位置變化的規律，驗證了所建模型的正確性。
  18. The distribution of the bend stress of fg has been gotten. the investigation on the contact stress of fg drive is made by fea. the distribution of the contact stress of fg is obtained in the different meshing locations during the meshing

    在面齒輪傳動的接觸應力的研究中，利用有限元分析法對面齒輪的接觸應力作了分析;獲得了在嚙合過程中不同的嚙合位置面齒輪的接觸應力的分佈規律。
  19. 4 、 on the basis of analyse of a quasi - static meshing simulation in a meshing period, a dynamic meshing simulation in the case of definite torque and rotary speed are carried out in a meshing period. the numerical results which indicating the variety of the contact status, the contact stress, the bending stress in the location of teeth root and the torque and rotary speed of gear pair vs the different meshing position are presented

    4 、在對螺旋錐齒輪準靜態嚙合進行模擬分析的基礎上，進行了螺旋錐齒輪動態瞬態嚙合模擬分析，重點分析帶載啟動時出現的沖擊現象，得出了齒輪的接觸狀態、接觸應力、齒根彎曲應力及主從動齒輪的扭矩、轉速和加速度隨嚙合位置變化的規律。
  20. 4 ) combining the local synthesis method for the machine - tool setting parameters, tca and ltca, and the numerical simulation of stress procedure constructs the optimal design circle with feedback. the developed software system provides an efficient design tool for the spiral bevel gears with excellent transmission behavior, high strength and lower noise

    4 ）結合加工參數設計的局部綜合法、幾何接觸分析（ tca ） 、承載接觸分析（ ltca ）及應力過程數值模擬，構成了具有反饋的閉環優化設計迴路，並形成了相應的軟體系統，為設計嚙合性能良好、高強度、低噪聲的弧齒錐齒輪傳動提供了有效的工具。
分享友人
分享到 Line

分享到臉書