轉爐氣 的英文怎麼說
中文拼音 [zhuǎnlúqì]
轉爐氣
英文
converter gas-
Such as 180 t oxygen converter, 1550 250 mm plate suspending straightening machine, annealing furnace of the whole hydrogeb mask, 1250mm cantalever straightener etc.
如180t氧氣頂吹轉爐， 1550250mm板坯連鑄機， 1829球磨機，全氫罩式退火爐， 1250mm懸臂矯直機等。Oxygen - natural rotating gas furnace for cast iron melting
熔煉鑄鐵用氧氣183 ;天然氣回轉爐Specifically for the iron and steel industry during the past 15 years, thermo electron has installed over 100 mass spectrometers for gas analysis applications involving the following plants : coke ovens, blast furnace ( bf ), direct reduction iron ( dri ), basic oxygen furnace ( bof ), electric arc furnace ( eaf ), argon oxygen decarburization ( aod ) furnace, vacuum oxygen decarburization vod furnace and ruhrstahl - hausen ( rh ) furnace
尤其在過去15年的鋼鐵行業中，超過100臺過程質譜儀用於氣體分析，包含：焦爐，高爐，直接還原煉鐵爐，氧氣頂吹轉爐，電弧爐，氬氧脫碳轉爐，真空氧氣脫碳爐和循環法真空脫碳爐。Equipment for the conversion to gas of central heating boilers built for solid and liquid fuels. atmospheric burners
使固體或液體燃料轉換成集中供熱鍋爐氣體的設備.大氣式燃燒器Main products made in our factory cover magnesia carbon brick, alumina magnesia carbon brick and carbonless brick and carbonless brick for converter, electric furnace and ladle finer as well as slide plate, pocket block, vent brick and impact plate ; pouring materials for converter ladle, gunning refractory for pouring basket, chrome conduction agent, carburant and other unshaped refractory
我廠的主要產品有:轉爐、電爐、鋼包精練爐用鎂碳磚、鋁鎂碳磚、無碳磚及板、水口、座磚、透氣磚、沖擊板等；轉爐鋼包澆注料、中間包用噴補料、鉻質引流劑、增碳劑等不定耐火材料。The discharge into the atmosphere of converter gas, acetylene, yellow phosphoric tail gas engendered by the electric furnace process, and organic hydrocarbon tail gas must be reported to the local administrative department of environmental protection for approval
向大氣排放轉爐氣、電石氣、電爐法黃磷尾氣、有機烴類尾氣的，須報經當地環境保護行政主管部門批準。Dry dedusting technique for converter flue gas adopted in steel works of china
轉爐煤氣干法除塵技術在國內鋼廠的應用The existing maerz kilns are of circular type with shaft cross sections in the burning zone of 7. 1 m
即將作為燃料的轉爐煤氣來自當地鋼鐵製造廠，具有Basic oxygen furnace
氧氣頂吹轉爐The iron is converted into steel in the bof using oxygen to remove impurities such as carbon
在氧氣頂吹轉爐中，通過氧除去碳等雜質將鐵轉為鋼。The objects and significance of automatic control in steelmaking and gas analysis in converter dynamic control are introduced
摘要介紹了目前國內外煉鋼過程的自動化控制的意義及其現狀，闡述了轉爐爐氣分析動態控制技術的基本組成和工作原理。Applying the mass balance and the reaction equilibrium theory, a dynamic model of carbon content and temperature variation of bof steelmaking process based on the continuous data from the exhaust gas analysis system was built
摘要根據物料平衡及反應平衡原理，利用爐氣分析系統在線連續檢測、分析數據，建立了轉爐冶煉過程中碳含量及溫度變化的動態模型。The results showed that the melting ratio of silica flux decreases and the complete melting time prolongs with the size of silica flux and matte grade increasing, and the effect of the blowing air and oxygen enrichment is not remarkable in the high grade copper matte converting process
對于高品位冰銅轉爐吹煉，鼓入氣體流量和氧濃度對石英熔劑熔化率影響不顯著；熔劑粒度和冰銅品位對熔化率影響顯著，並隨著熔劑粒度和冰銅品位的增加，熔劑熔化率降低，完全熔化時間延長。Bof basic oxygen furnace
堿性氧氣轉爐Technology of recovering converter waste gas by pressure swing adsorption
變壓吸附法回收煉鋼轉爐氣技術Influence of converter steel production on co2 content in the air of oxygen production stations
煉鋼轉爐生產對氧氣站區空氣中二氧化碳含量的影響China conversion of the existing 2x300 tpd coal dust fired lime kilns to converter gas firing
煤粉燒石灰窯轉換為轉爐煤氣燒窯Numerical simulation of temperature decrease and fluid flow with water spraying in venturi tube of converter coal gas recovery system
轉爐煤氣回收系統文氏管噴淋降溫與流動數值模擬Basic oxygen converter
鹼性氧氣轉爐The thin slab continuous casting and continuous rolling technology that was adopted by zhugang is an important technological revolution after the development of oxygen converter and continuous casting in the world iron and steel making industry field. in comparison to the conventional hot strip and sheet rolling technology the new technology has advantages such as saving investment cost, increasing finish product yield, decreasing production cost and shorting production cycle in large scale
珠鋼選用的薄板坯連鑄連軋工藝是世界鋼鐵工業領域中，繼氧氣轉爐煉鋼、連續鑄鋼之後的重大技術革命，與傳統的熱軋板材生產工藝相比，它具有節約投資、提高成材率、降低生產成本、大幅度縮短生產周期等優勢分享友人