轉矩環路 的英文怎麼說
中文拼音 [zhuǎnjǔhuánlù]
轉矩環路
英文
torque loop-
Two nonlinear simulation methods are designed by curve fitting method and anfis which seem simply and right in the simulation experiment. based on the model different control strategies also were realized in detail such as chopped current control ( ccc ), angular position control ( apc ), amplitude - change ccc and pi control. a simple torque sharing function ( tsf ) method and a tsf controller were designed which decreases torque ripple effectively
文章中還建立一種基於模糊神經網路的非線性模型，並對比分析了三種方法，模擬中確定了電機的最優開通關斷角，在此基礎上實現了電流斬波控制、角度位置控制、變幅值電流斬波控制以及分段雙閉環pi控制，模擬結果表明，它實現了電機的正常運行，很好的抑止了電機轉矩脈動，同時有效地降低了噪聲。Linear induction motor is an important kind of machines which have some merits such as simple structure, low cost, durability, convenience for maintenance etc. the subject of this thesis is to study a big circular ring linear induction motor, and the major works in this thesis are summarized as follows : ( 1 ) considering the effects of the finite length of primary core, one - dimension analytical solution for the air gap field is cited in this paper. based on it, the single layer winding magnetic field is studied. considering whole - pitched and short - pitched winding configuration with odd poles and half - fulled slots in both ends, the double - layer winding magnetic field is analyzed, respectively
本文對大圓環直線感應電機進行了深入細致研究，內容包括： （ 1 ）本文採用有限長行波面電流作用於有限長鐵芯上的模型，引用了氣隙磁場一維解，研究了單層繞組磁場，奇數極半填槽雙層繞組在採用整距和短距時磁場的分析、比較，簡單介紹了二維解； （ 2 ）用有限元軟體ansoft對大圓環直線感應電機空載氣隙磁場進行了靜態分析，並分析了結果； （ 3 ）用軟體進行了額定電壓下的瞬態分析，得到了轉矩，位移，轉速隨時間變化曲線圖，利用單極性霍爾元件測定轉速並與軟體計算結果進行了比較，採用等效電路法計算了堵轉時的最大電磁力並做實驗進行了驗證，由實驗測得了三相電流波形，並與計算結果進行了比較，對其不對稱性進行了定性分析。Aim at the dtc ' s blemish mentioned above and the direction of dtc technique development, the dissertation put great emphasis on the work as follows, with an eye to exalt dtc system function : ( 1 ) a new speed - flux observer of an induction motor is proposed to enhance the accuracy of flux observing, which is an adaptive closed - loop flux observer and different from the traditions. a new adaptive speed - observation - way is deduced out according to the popov ' s stability theories ; ( 2 ) to improve the performance of dtc at low speed operation, we have to exalt the accuracy of the stator flux estimation and a new way of bp neural network based on extended pidbp algorithm is given to estimate and tune the stator resistance of an induction motor to increase the accuracy of the stator flux estimation ; ( 3 ) digital signal processor is adopted to realize digital control. an device of direct torque control system is designed for experiment using tms320lf2407 chip produced by ti company ; ( 4 ) bring up a distributed direct torque control system based on sercos bus, sercos stand for serial real time communication system agreement which is most in keeping with synchronous with moderate motor control ; ( 5 ) the basic design frame of the hardware and software of the whole control system is given here and some concrete problem in the experiments is described here in detail
針對上面提到的直接轉矩控制的缺陷和未來直接轉矩控制技術發展方向，本論文重點做了以下幾個方面的工作，目的在於提高dtc系統的綜合性能： （ 1 ）提出一種新型的速度磁鏈觀測器，新型的速度磁鏈觀測器採用自適應閉環磁鏈觀測器代替傳統的積分器從而提高磁鏈觀測的精度，並且根據popov超穩定性理論推導出轉速的新型自適應收斂律； （ 2 ）改善系統的低速運行性能，主要從提高低速時對定子磁鏈的估計精度入手，提出了一種提高定子磁鏈觀測精度的新思路? ?利用基於bp網路增廣pidbp學習演算法來實時在線地修正定子電阻參數； （ 3 ）採用數字信號處理器dsp實現系統全數字化硬體控制，結合ti公司生產的tms320lf2407晶元，設計了直接轉矩控制系統的實驗裝置； （ 4 ）提出了基於sercos總線網路化分散式的直接轉矩控制系統， sercos （ serialrealtimecommunicationsystem ）是目前最適合同步和協調控制的串列實時通信協議； （ 5 ）基本勾勒出整個控制系統的硬體和軟體設計基本框架，詳細描述一些實驗中的具體的細節問題。Because direct torque control requires very high performance of real - time, the popular microcomputer core dsp is used as controller in the design of hardware. its high speed of running is suitable for the experiment. in the main circuit, there is a highly integrated power element : ipm as inverter, which includes seven igbt, has high switch frequency and fault diagnosis function
在本控制系統的具體實現上，由於直接轉矩控制對實時性要求很高，因此在硬體方面，採用了目前比較流行的數字信號處理器（ dsp ）作為系統的控制器，其處理速度高的特點正好符合本實驗的需要：在主電路中，本系統使用了集成度高的功率器件：智能功率模塊（ ipm ） ，作為逆變環節，其集成了七個igbt ，實現了高開關頻率逆變以及故障診斷的功能，從而使控制系統的體積大大縮小、控制更加靈活。Due to the direct torque control requires very high performance of real - time, the popular microcomputer core dsp is used as controller in the design of hardware. its high speed of running is suitable to the experiment. in the main circuit, there is a highly integrated power element : ipm as inverter, which includes seven igbt, has high switch frequency and fault diagnosis function
在本控制系統的具體實現上，由於直接轉矩控制對實時性要求很高，因此在硬體方面，本課題採用了目前比較流行的數字信號處理器（ dsp ）作為本實驗的控制器，其處理速度高的特點正好符合本實驗的需要；在主電路中，本系統使用了集成度高的功率器件：智能功率模塊（ ipm ） ，作為逆變環節，其集成了七個igbt ，實現了高開關頻率逆變以及故障診斷的功能，從而使控制系統的體積大大縮小、控制更加靈活。分享友人